Inspection Lot For Calibration Order in CRTD status

[Former Member]

Hi All,

I am creating calibration order through schedule maintanance plan by IP01, IP10, IP30, IP24.

Order is created and inspection lot 14 also generated.

But Inspection lot in CRTD status.

Find Attached document.

Please tell the possible reasons for that

  Thanks,

  Parag

[former_member620323 · Accepted solution]

Hi,

I couldn't find your attachment. However Have you created Task list ?

If Yes, then Please Check Sampling Procedure attached or not in Characteristic overview, Inspection points 300 (Inspection point for equipment) in Header Screen.

[Former Member · Accepted solution]

Hi Rahul,

There is no sampling procedure in business process thats why we are not attached sampleing procedure.

Inspection point 300 is already in task list. any other setting required.

[former_member184536 · Accepted solution]

Hi Parag

You have to maintain sampling procedure as without sample calculation Lot will not get Status REL.

Regards

Manish

[Former Member · Accepted solution]

Hi Manish,

But without sampling procedure for inspection type 01, 03, 04 lot should be in released status.

then whtais the problem of inspection type 14.

[nitin_jinagal · Accepted solution]

Hi Parag,

Did you run a test scenario with sampling scenario? And did you check what Erik has mentioned?

Regards,

ntn

[Former Member · Accepted solution]

Hi Ntn,

No, i will execute this scenario right now. yes i have checked but still in CRDT status. 

[Former Member · Accepted solution]

Hi Ntn,

If sampling procedure is maintained then inspection lot in released status, but is it required new UD code for Equipment.

[former_member620323 · Accepted solution]

No You can use Standard UD Code. For this You have to assign Selected Set in Inspection Type 14 as per attached Screen shot.

Go to QCC3-> Inspection Lot Creation-> Maintain Inspection Types.

After Maintaining this Selected Set for Insp. Type 14, System will Show you the Same UD Code at the time of Usage Decision.

Still if you want your Code only then you have to customized by using Tcode QS41 & QS51.

[nitin_jinagal · Accepted solution]

No Parag,

There is no impact on UD selected set.

ntn

[Former Member · Accepted solution]

Hi Rahul,

But in my inspection type 14 already EQT selected sets are assigned in that case maintain code group and codes to EQT selected sets am i right or not.

[Former Member · Accepted solution]

Hi Ntn,

But in my inspection type 14 already EQT selected sets are assigned in that case maintain code group and codes to EQT selected sets am i right or not.

[nitin_jinagal · Accepted solution]

I didn't get your point. If you have correctly maintained in config setting as per the snap given by Rahul, you should not face any issue while making UD for the inspection lot.

ntn

[former_member620323 · Accepted solution]

Please check the UD Selected Set Code in QS51 by Entering EQT Selected set & See whats code are maintained. If its right codes then don't do any changes in that & use it.

[Former Member · Accepted solution]

Hi Rahul,

I have maintained selcted sets for EQT problem is solved.

Thnx.

[Former Member · Accepted solution]

Problem is solved. thnx

[nitin_jinagal · Accepted solution]

Hi Parag,

if the query is resolved, then please don't leave the thread open. Mark helpful and correct answer and pl close this thread

ntn

[Former Member · Accepted solution]

Hi Ntn,

yes i am busy in meeting thats why delay in closing the thread.

[Former Member · Accepted solution]

Hi Ntn,

One thing i will ask you if my business not using sampling procedure in that case what will be the solution.

[nitin_jinagal · Accepted solution]

Hi Parag,

I explained this before also. A dummy sampling procedure can be made.

"you can make a sampling procedure with Fixed sample. Maintain sample size as 1 and acceptance number 0. This way there won't be any impact of SP (tick only sampling procedure in the control indicators of MIC)"

In addition, you do not set indicators for Additive and Destructive in control indicators for MICs.

This way you would be able to map sampling procedure.

Hope you got the point.

Regards,

ntn

[Former Member · Accepted solution]

Hi Ntn,

ok, thnx a lot.