How Enhanced Interface Determination will work in PI 7.3 Single Stack?

[jegathees_waran]

Hello Friends,

We have PO 7.3 EHP 1 SP04 Single Java Stack.

We created 1..N Mapping. (The mapping is between One Outbound Interface -> One inbound interface with two operations).

This works fine in PI 7.1 classical configuration.

In PO 7.3 Single Java Stack,  only ICOs (Integrated configuration) are the option to configure.

In ICO, this operation mapping (1..N) is not detected.

Could you please clarify how this can be achieved?

Kind regards,

Jegathees P.

[former_member184789 · Accepted solution]

Go to your operation mapp, & press F7 to check if there are any issues with the operation mapping

[jegathees_waran · Accepted solution]

Hello Adarsh,

I tried all the way.

1. Change the occurrence of both source interface and target interface with two operations as 0..1

2. In the target side, instead of single service interface with two operations, I use two inbound service interface in the target side in operation mapping.

In any of the case, this operation mapping is not detected in ID. (ICO).

I don't have a clue where is the problem..

I am wondering these are the frequent requirements in business.. how to implement this using ICO, either my tries are wrong/SAP doesn't provide this feature...

Kind regards,

Jegathees P.

[aashish_sinha · Accepted solution]

Hi Jegathees,

I can see problem is occurrence of source structure in message mapping. Go to signature tab, change occurrence of source message to 1. Let other settings intact like I told you earlier.

Regards

Aashish Sina

[jegathees_waran · Accepted solution]

Hello Aashish

Thank you very much for your quick reply. I tried the same way as you suggested. On the Source Side occurrence as 1 and the target side occurrence as 0..unbounded.

It worked.  Thanks a lot.

Kind regards,

Jegathees P.

[aashish_sinha]

Hi,

Can you please do below things -

1. Check Message Mapping Signature TAB - in target structure, Change occurrences to 0..n for all message types.

2. Check operations mapping if target service interface occurrence is 0..n. if not, change it to 0..n.

3. go to ID - ICO - delete operations mapping and assign it again.

Now you are ready for 1:n multimapping in PI 7.31 SP04. If you still getting issue in message monitoring for  java error, upgrade PI 7.31 to SP05.

Regards

Aashish Sinha

[former_member201264]

Hi,

Can you check the below link for the limitation of the Limitations of SAP PI 7.3(single-stack Java installation).

http://scn.sap.com/docs/DOC-27374.

Here it says that Extended  receiver determination is not working in PI 7.3 single stack.

Check the same for Enhanced Interface Determination here.

Regards,

Sreeni.

[former_member184789]

Hi,

You have given occurrences of interfaces as unbounded..I am not sure if this is supported..For the time being, add interfaces with single occurrence & see if it works..

[former_member191435]

HI Jegathees,

Can you please check your service interfaces properly..... and try to create once again it should be work. Still if you are facing the issues please share the screen shot will let u know..

Thanks,

Sreenivas

[jegathees_waran]

Hello Adarsh & Sreenivas

Thank you very much for your reply.

I checked again. The Service Interfaces are syntactically correct. Given below are the attributes:

Outbound Service Interface

-----------------------------------

Category: Outbound

Interface Pattern : Stateless

Security Profile : Low

Mode: Asynchronous

Inbound Service Interfaces with 2 operations

---------------------------------------------------------

Category: Inbound

Interface Pattern: Stateless

Security Profile: Low

Mode: Asynchronous

When we checked and tested the operation mapping, it works fine.

In ICO, when we select the operation mapping, (Tab Receiver Interfaces), it shows 'No suitable data found'.

Please find the screen shot given below for your reference.

Could you please clarify why the mapping is not detected ?

[jegathees_waran]

Hi Adarsh

Could you please check my service interfaces with your service interfaces and kindly clarify what's the error in this.

Also what's the SP level of your PO system. (Ours is PO 7.3 EHP 1 SP 04)

From the screen shot (ICO), it is working for you and not working for me.

Kind regards,

Jegathees P.

[baskar_gopalakrishnan2]

You might want to check this blog

http://scn.sap.com/community/pi-and-soa-middleware/blog/2013/04/03/setup-multiple-operations-scenari...

The blog shows PI 7.31 sp 5

[former_member184789]

Hi,

Can u pls tell where are u getting error? I also tried creating such a scenario in ICo, but the operation mapping is detected as usual. See below: