Skip to Content
avatar image
Former Member

Change the inspection stock of material xxxx in QM only

Hi,

I am facing error at the time of GR in MIGO as below:

"Change the inspection stock of material xxxx in QM only"

1. I have created material with QM view wherein I have activate inspection type 01.

Note: In default value of inspection type 01, there is no check mark for Post to insp. stock. I have marked this check box for the said material.

2. Created PO.

3. Try to do GR in MIGO but facing above error.

Case 2:

Inspection lot do not get created even inspection type 01 is activated in above case when check mark is not tick for Post to insp. stock. As per my understanding inspection lot should create & stock should post to unrestricted.

Please clear this.

Rajesh.

Add comment
10|10000 characters needed characters exceeded

  • Follow
  • Get RSS Feed

5 Answers

  • avatar image
    Former Member
    Feb 07, 2013 at 11:32 AM

    are you getting error message as QA495 then

    try to deactivate the SAP enhancement QAAT0001 in CMOD/SMOD

    and test this issue again?

    or

    This problem is most typically resolved by executing the report ZQEVAC20 contained in note 48815 to repair any inconsistencies which may exist.Please execute this report. If this does not resolve the problem,then please review and apply notes 86638 and 212238.048815 Checking possible inconsistencies between MM and QM 086638

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Feb 06, 2013 at 12:10 PM

    Please provide the screen shots of the following documents.

    1. Material Master with 01 Inspection type & its default values
    2. Goods Receipt document with Stock type & movement type in Items details screen
    3. Inspection Plan created for that Material with usage as mentioned in your Inspection type configuration (if this is not created, create one & try again)
    4. Also try Physical sample with Unknown sample type in Inspection Type configuration
    5. As Goods receipt Inspection type (01) physical sample refers the Goods receipt sample which is managed with goods movement only, you may need to copy that with your own settings if you don't want to post the qty Quality Inspection stock as well as SPRQ Inspection lot status should not be shown.
    Add comment
    10|10000 characters needed characters exceeded

  • Feb 06, 2013 at 12:17 PM

    Yes Your understanding is correct.

    When you do GR of material those you unmark the post to inspection stock, then system should create Inspection lot & the stock of those GR directly go to the Unrestricted use stock.

    This is the standard one practice.

    In your 1st case, I thing you mark post to inspection stock & stock goes into Quality Inspection stock. For This Quality stock you have to post through Usage decision only not by doing MIGO by 321 mov. type.

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Feb 07, 2013 at 03:22 AM

    I will reply to your second question initially,

    Check when QM view >>Inspection type was active & when PO was created.

    during creation of PO if Inspection type was active then "LOT SHOULD BE CREATED" after MIGO>>101 mvt.

    For the first Qustion ,check the stock type during MIGO.it should be "qulaity".If not chnage it & check again.

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Hi Sujit,

      It's confirmed that Inspection type 01 was active & when PO was created but even Inspection lot do not created after GR.

      In default value of Inspection Type Post to insp. stock is unmarked.

      I am getting above said error at GR when inspection type 01 active when I check mark of Post to insp. stock in QM view.

      Any further solution.

  • avatar image
    Former Member
    Apr 02, 2015 at 12:10 PM

    Dear All,

    I am facing the same error while doing PGR through VL01N.

    ERROR Message: 495 QA: Chamne the inspection stock of material XXXXXXXXX in QM only.

    checked by maitaing 06 inspection type in material master but now resolved.

    Kindly revret on this.

    Add comment
    10|10000 characters needed characters exceeded