SAP Enterprise Portal NW 7.3 and SOLMAN 7.1 : not find in "Product Systems"

[Former Member]

Hello,

we tried to link

I have installed SAP Enterprise Portal Netweaver 7.3 and it was successufuly connected to SLD and LMDB of SOLMAN 7.1 (SPS02).

From SMSY, I can find this instance on "Technical systems" but not in "Product Systems".

When we tried to use Maintenance Optimizer to download SPS we got the following error : "System constellation is empty, calcultation will not run". Which I think it is related to "Product Systems" missing configuration. No product software has been detected in SLD nor in LMDB.

I added manually "Product instance" :SAP Netweaver 7.3: Enterprise Portal

When I try to add the same component in SLD : "Installed Products", I got the following error : "CIM_ERR_ALREADY_EXISTS: Instance already exists".

Do you have some advise ?

Regards,

Rodolphe

[nicholas_chang · Accepted solution]

Hi,

I did face the same problem when i first configured AS JAVA system and really struggle and grease my elbow to get it working.

I would advise your to upgrade to latest SP level, SP03 and also the CIM and CR Content for SLD to eliminate all possible bugs.

However you can try as below:

1) go to SMSY -> search for the SID instance

2) Highlight the SID and click "Change"

3) Technical system editor will prompt out, and you'll see no Product Version and Product System assigned.

4) Next, navigate to software component and click on "Software Component Versions" and assigned the correct product instance by click the fitting SC proposal. SAVE and leave the page.

5) Now, go to SOLMAN TX: LVSM and webdynpro will display

6) Ensure the Landscape verification job is full sync and completed. Else, you can trigger using LVSM_LOAD.

7) Go to tab "Errors Warnings" and look for the SID, and you'll see that product instance SID is not assign to a product system.

😎 on the same page, click "Add product system" and select the correct product and product version. For eg: Your product is Netweaver EHP2 you should first assign product as SAP Netweaver, and Version is EHP1.

9) Select the correct SID and correct Product Instance on the next screen, click Finish and SAVE once done. Remember, you can only select ONE PRODUCT INSTANCE HERE!!

10) Now, go back to Technical System Editor and change the entry for the particular SID.

11) Here, you can see the Product Versions and Product System is filled on the main object. Check all your entry and save is everything is correct.

12) Go back to SMSY, and you should able to see the SID is populated under the correct Product and Product Version.

13) Now in SMSY, you should able to change the data for Product System such as assign Installation no, read system number, sync with SAP and etc.

Hope it helps,

Cheers,

Nicholas Chang

[Former Member · Accepted solution]

Thanks a lot for your answer.

I follow your procedure, it is working.

And according the link :

http://wiki.sdn.sap.com/wiki/display/SMSETUP/MaintenanceofProductintheSystemLandscape

I find the status of the support of Enterprise Portal in SOLMAN 7.1 : "Partly"

Installed software components are provided automatically but product versions and product instances need to be assigned manually.

For your information, we already used the SP03 on SOLMAN 7.1.

Regards and thanks again,

Rodolphe

[nicholas_chang · Accepted solution]

Hi,

Glad that it helps. Agree with the wiki that says we need to manually assigned, but it never guide us on HOW TO ASSIGN. The procedure in SOLMAN7.1 is not as simple as previous version where SMSY, LMDB, Landscape verification is involved.

Please mark this thread as closed with answered so that it'll help others in near future, and award points if you find it helpful.

Cheers,

Nicholas Chang

[sunny_pahuja2]

Hi,

Upload latest xml in solution manager from SAP Note 1603103 - SMSY NetWeaver 7.3 upgrade.

Thanks

Sunny