SLD Data Supplier for ABAP

[Former Member]

Hi,

Firstly i defined RFC destintion and JCO RFC Destination SLD_NUC2, tested it in sm59 and OK. After i run rz70 and it give me followign error.

-

---

0: sapnt_IBS_00 : Execute program: SLDAPPL_SERV

0: sapnt_IBS_00 : Execute program: SLDBCSYS

0: sapnt_IBS_00 : Execute program: SLDCLIENT

0: sapnt_IBS_00 : Execute program: SLDCOMPSYS

0: sapnt_IBS_00 : Execute program: SLDDBSYS

0: sapnt_IBS_00 : Execute program: SLDGWSRV

0: sapnt_IBS_00 : Execute program: SLDINSTSC

0: sapnt_IBS_00 : Execute program: SLDINSTSP

0: sapnt_IBS_00 : Execute program: SLDIPSERV

0: sapnt_IBS_00 : Execute program: SLDMSGSRV

0: sapnt_IBS_00 : Execute program: SLDASSOC

0: sapnt_IBS_00 : Collection of SLD data finished

0: sapnt_IBS_00 : Data collected successfully

0: sapnt_IBS_00 : RFC data prepared

0: sapnt_IBS_00 : Used RFC destination: SLD_NUC2

0: sapnt_IBS_00 : RFC call failed: JCO.Server could not find server function 'SET_SLD_DATA'

0: sapnt_IBS_00 : Batch job not scheduled

-

---

Following error from sld server log:

#44 04/09/2005 20:43:49.412 [JCO.ServerThread-25] ERROR com.sap.lcr.sagent.SAPProxyServer: JCO Server exception raised: JCO.Server could not find server function 'SET_SLD_DATA'

Thrown:

com.sap.mw.jco.JCO$Exception: (123) JCO_ERROR_FUNCTION_NOT_FOUND: JCO.Server could not find server function 'SET_SLD_DATA'

at com.sap.mw.jco.MiddlewareJRfc$Server.dispatchRequest(MiddlewareJRfc.java:2029)

at com.sap.mw.jco.MiddlewareJRfc$Server.listen(MiddlewareJRfc.java:1520)

at com.sap.mw.jco.JCO$Server.listen(JCO.java:6926)

at com.sap.mw.jco.JCO$Server.run(JCO.java:6855)

at java.lang.Thread.run(Thread.java:534)

What is the problem?

Regards,

Altug Bayram

[Former Member]

Hi RK

How can I do that, is there any guide which I can refer to?

Thank you

//psl

[Former Member]

To overcome the problem

"JCO.Server could not find server function 'SET_SLD_DATA" while using RZ70 make sure that all your SLD Profile parametsr are right.

For Instance I got this error when during PI HCOPY.

The target SLD had some profile parameters(SLD Profile) that were relevant to source.

After changing them the message no longer appeared.

Regards

Naresh P.

[Former Member]

Hi

I hit the same problem, SLD has been configured according to post-installation guide, but what specific setting I have to checked for this error?

Thank you

//psl

#44 04/09/2005 20:43:49.412 [JCO.ServerThread-25] ERROR com.sap.lcr.sagent.SAPProxyServer: JCO Server exception raised: JCO.Server could not find server function 'SET_SLD_DATA'

Thrown:

com.sap.mw.jco.JCO$Exception: (123) JCO_ERROR_FUNCTION_NOT_FOUND: JCO.Server could not find server function 'SET_SLD_DATA'

[Former Member]

HI PSL,

Have you configured JCO there are i think five steps have you through with all the steps and checked the connection may be here you not abel establish the proper connection

try it out..

Regards,

RK

[Former Member]

Hi

Heve you configured SLD and JCO settings properly check once

http://servername:<port>/sld

http://servername:<port>/welcome.

hope this may solve your problem

Regards,

RK