Skip to Content
author's profile photo Former Member
Former Member

repair full load

Hi,

I have "Billing document" number( 9000182) in ODS .

For the debugging purpose I want to do " REPAIR FULL LOAD' only for this document .

can i do repiar FULL LOAD" for this documetn in Production system?. Is there any problem if i do repair full load. any data mismatch occurs.

I can do selective deletion and i can do " REPAIR FULL LOAD' but my doubt is any problem will come as it is ' PRODUCTION System".

Please confirm .U r suggestions will be helpful.

i tried in Q system but that document was not there in R/3.

Add a comment
10|10000 characters needed characters exceeded

Related questions

6 Answers

  • Best Answer
    author's profile photo Former Member
    Former Member
    Posted on Jul 18, 2011 at 10:12 AM

    Hi Kotha,

    If you are doing this for debugging purpose,Then no need to delete the data from ODS.

    Follow the below steps.

    1) Run IP with options "load till PSA" and selections for Billing no 9000182(If you think it will run for longtime,do full repair or run it as full load)

    2)If you want to check thi data in CUBE's as well then run in simulation mode using Update rules with respect to each target.

    Hope this helps.

    Regards,

    Venkatesh

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Jul 18, 2011 at 11:27 AM

    Hi,

    So you want to reload a document from R3 to your DSO?

    Are your key figures in overwrite?

    If there are in overwrite, then you don't need to delete any data in your DSO.

    If there aren't in overwrite, then you will have to do a selective deletion.

    The next steps you will need to execute as well:

    I suppose that you are talking about datasource 2LIS_13*?

    A) delete the setup table

    B) fill the setup table with the document

    C) create an infopackage with the "full repair" flag on, and start loading the data.

    Regards,

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Jul 18, 2011 at 08:46 AM

    hi,

    You need to selectively delete this billing document from all the target cubes, then delete it from the DSO and after that perform selective full repair. This won't create any problems.

    regards,

    Arvind.

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Jul 18, 2011 at 09:42 AM

    Hi,

    You have to do the selective delection all data targets where it is used after that you can do repair full load.

    Thanks and Regards,

    Venkat.

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Jul 18, 2011 at 10:01 AM

    Hi Kotha,

    You should not perform selective deletion unnessarily. It would create problems in production.

    Since , it is only for debugging, you can debug in simulation mode. This way you would not have loaded anything to the DSO.

    Even if you have loaded it would be only till the new data table. This you can delete later on.

    Please ensure that the process chains are not loading this target, when you are testing.

    Thanks,

    Krishnan

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Jul 18, 2011 at 10:06 AM

    Hi,

    If your Billing Doc is not there in any data marts, you can do Repair full without deleting from DSO, because DSO has got overwriting functionality.

    Regards,

    Suman

    Add a comment
    10|10000 characters needed characters exceeded

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.