on 03-16-2011 1:18 PM
Hi Experts,
I'm facing the problem, that, to my opinion, system provides too many filter values.
"Zero Suppression" is active, "Filter Value Selection" is set to "Only Posted Values...",
so I would expect that the amount of values suggested for filter is the same as the
amonunt of characteristics displayed in my report. BUT.... it's larger, also thoe values are provided,
that are suppressed because the key figures are zero in report. Is this a regular behaviour?
Display in Report
Profit KF1
Center
6551 2000
5562 4000
5589 0 (suppressed)
5593 0 (suppressed)
Selectable Filter values for Profit Center
6551
5562
5589
5593
Expected
6551
5562
I.m not really sure, but i think in 3.5. both amounts were equal.
Currently we are on 700, SP21, GUI 720, PL3.
Thanks in advance for help.
Regards
Joe
Hi,
you can check it by putting condition :-
KF is not Equal 0
Best Regards
Obaid
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Result of furhrer researches:
"Zero suppression and consitons are processed
at the frontend and don't impact the backend."
Will open another threat to learn about the difference and the interface of both.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Guys,
Thanks for repiles. Substituted zero suppreesion by conditions, but result was the same.
i also thought, that filters are not affected by zero suppreesion or conditions, becausethese
options just control display and not reading of database.
But I found a note, that confused me. a lille.
Quotation from nots 988523 - F4-Filter Q mode special behaviours: drilldown + conditions
Symptom
This note describes certain special behaviours of the F4-Selection on a characteristic from the navigation block of the query when the "Filter Value Selection" is set to "Only Posted Values..." in RSD1. This setting is also called called Q-mode.
Case 1: When the characteristic is not in Drilldown.(i.e the characteristic is a Free characteristic)
When we filter on a characteristic before drilldown, OLAP will fetch a SUPERSET of the data to be returned. Since the chararcteristic is not in DRILLDOWN, OLAP takes the best GUESS of the probable values for the filter and delivers a SUPERSET.
Hence in such cases we could see, more values returned by the FILTER than the actual values one would expect.
However, once we drilldown, OLAP knows the exact values for which data is available in the report and hence would fetch the exact result set. This value is filled in the cache and subsequently filtering on the characteristic will always give CORRECT values immaterial if the characteristic is Drilldown or not.
.....
Either I misundersttod it or there is a bug in NEx Analyzer.
Regards
Joe
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
According to me it will not harm to the filters
If u use settings active (all values = 0) then only ROWS & COLUMNS with 0(ZERO ) will not appear
If u use settings active then only ROWS & COLUMNS Result with 0(ZERO ) then that ROWS & COLUMNS will not appear..
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
I belive Suppression does not impact the Filter Values. It is just for display purpose.
May be you cna try creating the condition in your query where KF is greater than 0.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
89 | |
10 | |
9 | |
9 | |
9 | |
6 | |
6 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.