cancel
Showing results for 
Search instead for 
Did you mean: 

MM02 --> classification view: when F4 to select value layout differences

Former Member
0 Kudos

Hi

Development system:

When i try to chage a material [MM02] and go to classification view. i want to select a value for a characteristis. I presed F4, i could see possible values for that characteristic. it just has one column showing possible characteristic values

In Other system [Pre production] for same material when F4 is pressed i could see columns like characteristic value, description, Document, Expl etc

User is questioning why layout different in diff systems when F4 is pressed to select a characteristic value

any pointers, please help

Accepted Solutions (1)

Accepted Solutions (1)

Former Member
0 Kudos

Hi There

In MM02-Classification-Values(F4) in the right hand side top corner- You will find the configuration icon- there you can define the layout as you wish,,

if you want to get all the details, click on the administrator-there uncheck the invicible fileds- then you can check all the fiels in both the system,,

Try it out if you have any doubts reply back

Thanks

Senthil

Former Member
0 Kudos

Thanks for reply, i just checked none of the field is marked invisible in both systems. settings same

i am getting diff layout when i clcked on any characteristic row and pressed F4 to select a value for the characteristic

PreProduction sys: i could see only one column - characteristic values

Developmen sys: i could see columns like characteristic Values, Characteristic descrption, object, Document, Expl etc

Former Member
0 Kudos

Hi

As i said earliar go to the Characterisitics Values- F4 to select the possible values- There click on the Configuration- Point to check is Current Settings and Std Settings,, (if both are Basic settings then fine, If different then in Variant select the Current setting Variant and Click on the administrator) there you will find the Invisible enabled,,

Coz other than there is no way to manage this layout,,

Thanks

Senthil

rafael_zaragatzky
Active Contributor
0 Kudos

Hi Sasi,

In you first message your described what you see in the dev. systam and the pre-prod. system the other way around!

Never mind.

I would suggest you clicking once on the name of the characteristic on the classification view of the material master and then pressing F1. Here you see the whole definition of the charateristic. Do the same in both systems in two parallel windows and compare all the settings. Pay special attention to the tab "Values", the checkbox "Additional values" there and the pushbutton "Other value check". Another tab that can be of special importance is "Addnl data".

As you know, the characteristics can be created in each system independently, i.e. they could have been created a bit differently. It is possible to set up an ALE scenario for copying characteristics data from one system to another one, if you want to be completely sure.

BR

Raf

Former Member
0 Kudos

Senthil,

When F4 is done to see possible characteristic values i dont see any icon for configuration.

I am suspecting its more dependent on authorization.

Rafael,

What i told is right i see few more columns in development but not in preproduction

rafael_zaragatzky
Active Contributor
0 Kudos

Never mind, Sasi.

Have you compared the F1 screens in the development and the preprod. systems? What are your findings?

BR

Raf

Former Member
0 Kudos

Hi Sasi

After entering mm02 and clicking the classification view, You enter su53 in command field , their might be some missing authoraziation in pr-production. Maintain the missing authorisation objects to the ID and then check.

Cheers

Kris

Edited by: KRISHNA AKULA on Feb 8, 2011 12:59 PM

Former Member
0 Kudos

SU53 - authorization successfull

Charcteristics are created same way in both systems

I am suspecting since development is open system and since preproduction user will not have administrator access to any transaction this issue arising, not sure though

Former Member
0 Kudos

Hi Sasi

Agree with you,, There is a chance to have an authorization issue,,

But hwevr it is there will be an icon (Yellow, white and blue in three lines), you can get this config (for layout) in almost all the screens (like Me21n (item details), CT04 values screen )

Check with the Basis Team/security team to fix this issue,,,

Hope it helps

Thanks

Senthil

Former Member
0 Kudos

We could not resolve

When F4 is done user is expecting Characteristic value & value description too. Now only one column[Charcateristic value] appearing

Plz help

rafael_zaragatzky
Active Contributor
0 Kudos

Hi Sasi,

I wonder how your possible values for the characteristic are defined - some kind of check table or explicitly in the definition of the characteristic? In the latter case it can be that the list of values is defined in one system, but not in the other (since the characteristics are created independently in each system) or defined with a wrong language - not in the user's logon language.

BR

Raf

Former Member
0 Kudos

After F4 is pressed,

at right corner Layout changes config icon must appear. in our case it isnt

look like security issue

Thanks gurus for all the responses

Answers (0)