Skip to Content
avatar image
Former Member

RTP-interface for season+on\off peak cosumption (RTP component 0002)

Hello all!!!

I`m a beginner in SAP IS-U, so, I NEED YOUR HELP!!!

I want to use RTP interface with the RTP component 0002 (seasons+on\off consumtion). I checked period for seasons and period for on\ff peak - it is ok. I use formula LIMIT02 and 60 minits length. So, reasult parameters are:

1. on peak consumption below the limit

2.off peak cons below the limit

3.consumption above the limit

4.Amount above the limit

input parameters are:

consumption and limit for every block of RTP component + price in block "Default"

output parameters are:

1.consumption below the limit for all blocks of RTP componet exept "Default"

2. in the block "Default" - consumption above the limit and amount above the limit

In the rate I have standart steps:

1. IF02 EAMOUNT_7 EAMOUNT_0

2. QUANTI05 EAMOUNT_36

3. LUMSUM02 EAMOUNT_7 EFACTOR_1 EAMOUNT_6

4. ENDIF

5. QUANTI01 EQUANT_37 EPRICE_9 EAMOUNT_6

6. QUANTI01 EQUANT_38 EPRICE_10 EAMOUNT_6

For RTP operands I setted result parameters from RTP interface and for operands EPRICE_9 and EPRICE_10 - I created prices.

in the rate I cheked inconsistancy and it is correct. I updated scheme according the rate steps.

But the issue is: when I execute billing process I get values only for result parameters Consumtion above the limit and Amount above the limit.

I have such a feeling that system doesn`t recognize data in seasons and on\off periods of the day, it reads data only for block "Default"... maybe something else is needed to be customized in the system??? What I`m doing wrong??? please, can anybody explane me how to use correctly seasons and other periods in the billing???

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

3 Answers

  • avatar image
    Former Member
    Jul 18, 2010 at 05:47 PM

    Did you generate your RTP component? Check transaction EEDM_CMP02 and then generate.

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member Former Member

      Yes, i want to price consumption below according on\off peariods and season and consuptio above with a price from price profile. and in the rate and scheme i have step for amount above and different steps for for calculation of consumption below with different prices. may it be that programm for formula LIMIT02 takes into account only default parameters?

  • avatar image
    Former Member
    Jul 19, 2010 at 03:29 PM

    Hey,

    I am wondering why you want seasons, but I do not see this in your result parameters

    your result parameters are described as:

    1. on peak consumption below the limit

    2.off peak cons below the limit

    3.consumption above the limit

    4.Amount above the limit

    ad1) I would go with a quanti14 for every consumption (rate config)

    ad2) in the billing document there is a RTP-IF anaylsis tab, that shows for every hour, which consumption was found (good for analysis)

    ad3) I would double check your on-peak off-peak time configuration...EDM-> basic functions -> Time-of-use and factory calendar. (rtp-component config)

    hope this points in the right direction, regards,

    Tom

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      I found the mistake! for off peak period 2 intervals are needed: till 23:59:59 and from 00:00:00:))))))))) everything is simple as usually. Thank you eveybody!

  • avatar image
    Former Member
    Jul 20, 2010 at 11:29 AM

    Thank you!

    Add comment
    10|10000 characters needed characters exceeded