Skip to Content
avatar image
Former Member

To Clear the Quality Stock from MMBE

Hello!

I am having one problem in doing quality Inspection. one material is having quality stock in the Tcode MMBE.

but that particular item is not presenting in QA32 for doing inspection.I checked in Material master in the all the Inspection type is active.And i also checked the status SPRQ in QA32. it is not having the SPRQ status.So i tried MB1B Tcode to move the stock but it is showing error as 'Change the Inspection Stock of the material 6550005020 in QM only'.How to slove this problem or is there another solution to clear the inspection.The main aim is to clear the quality stock in mmbe, please help me if anybody knows the solution.

-regards,

M.Suba.

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

5 Answers

  • Best Answer
    avatar image
    Former Member
    Jun 15, 2010 at 09:21 AM

    Means the lot is created.Go to material document for that mvt & check there is Inspection lot number present.

    In QA32 it is just matter of selection.There must be a lot exists

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member Former Member

      dear

      go to MIGO->material doc----->disply ..............here in line item if lot is genarated then you can see the inspection lot tab.Kindly explore the same.

  • avatar image
    Former Member
    Jun 15, 2010 at 09:44 AM

    Hi,

    Check if you have the correction report ZQEVAC20 and if existing, pls run it and try again. this will clear all the incosistencies between MM and QM.

    OSS Note number is 48815.

    Thanks& Regards,

    Srinivas.D

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jun 15, 2010 at 09:57 AM

    The main aim is to clear the quality stock in mmbe

    Activate inspection type 05 and try to transfer the material from quality in MB1B (Mvmt type 321). Though I am not sure, but this might be helpful.

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Hello!

      I already tried this method MB1B with 321 movement only. but it is showing error that 'Material should be inspected in QM only'. I am unable to move the stock through this method. could u please tell me proper way to transfer the stock or else some other way to move the stock

      -Thanks & regards,

      M.Suba.

  • Jun 15, 2010 at 10:38 AM

    Hello M.Suba.,

    Well I find 2 contradictory statements here.

    1. one material is having quality stock in the Tcode MMBE.but that particular item is not presenting in QA32 for doing inspection

    2. And i also checked the status SPRQ in QA32. it is not having the SPRQ status

    If lot is not created how and where did you check the status of lot?

    The situation narrated by you arises in either of following cases.

    1. Lot created with SPRQ status. Use gave UD before stock posting. In such cases go to t-code QVM2. Find the open lot and post the stock.

    2. Lot did not create and stock posted to quality inspection. In such case you have to do 321 movement through MB1B. But this is not your case. Since you are getting error as 'Change the Inspection Stock of the material 6550005020 in QM only inspection lot exists. Just check in QVM2

    3. The last possibility is inconsistencies in MM and QM module. For this apply note 48815 as suggested by Srinivas.D

    Best Regards,

    Anand Rao

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Sir,

      First I Thank for ur reply.In MMBE the total Quantity of the stock Present for the particular item is 410.In QA32 i gave the following input,

      plant=>Lp01

      -Inspection lot origin=>empty

      -Date=>empty

      -Material=>6550005020

      -Option Button =>select All Inspection lot

      There i found the Status 'SPRQ' with 1 Quantity that i cleared in QA32 screen itself. So the remaing stock 409 is presenting in MMBE.

      After that i didnt find the Inspection lot to clear that material in QA32.I also tried the the same in QVM2.same like QA32 material is not displaying in QVM2 also.

      I also tried MB1B screen with movement type 321 there i am getting error 'Material should be Inspected only in QM'. so that also becomes failure to me.

      But in Material master Inspection type is active only.

      Plz give me a solution to clear that stock from Quality in MMBE.

      -Thanks & regards,

      M.Suba.

  • avatar image
    Former Member
    Dec 03, 2010 at 09:27 AM

    answered

    Add comment
    10|10000 characters needed characters exceeded