Skip to Content
avatar image
Former Member

Creating Inbound delivery using MIGO ( movt 501). Error Message

Hi All,

I am creating an inbound delivery without reference(movt type 501) in MIGO. I am getting an error message : Data for creating delivery is incomplete(Customer).

Is there some configuration that I need to maintain to ensure the delivery is created before using transaction MIGO?

I am trying to create the inbound delivery in 4.6c.

Thanks,

Arup

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

8 Answers

  • Best Answer
    avatar image
    Former Member
    Jun 09, 2010 at 11:09 PM

    Further please check:

    1) If the plant has customer # and vendor # in table T001W.

    2) Check the respective distribution channel or division with which you work in the delivery, if a reference distribution channel or a reference division has been defined.

    3) The error message ( E279- I hope this is the one you are encountering) figures several times in include 'MM07MFS0_SD_LIEFERUNG_ERGAENZE' of program MM07MFS0. Sit with an ABAPer to figure out what's missing.

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Hi Chandrashekhar,

      So here are things that I needed to clarify.

      1. I had configured the system in ECC 6.0 and did not enter any specifics for entries in Table T001W. I do not see entries in T001W in 4.6c either? Is it mandatory to have the entries in this table? ECC 6.0 had no issues whatsoever when using MIGO.

      2. No shipping conditions have been maintained.

      3. I am an ABAP programmer myself so I was curious to know if you had ever encountered this issue while looking at the above program that you have mentioned? I can debug the program but was wondering if there are some specifics that you have already encountered?

      Thanks,

      Arup

  • avatar image
    Former Member
    Jun 09, 2010 at 10:29 PM

    Hello Arup

    Check the Vendor master data: Address- Transportation zone, Shipping conditions.

    Add comment
    10|10000 characters needed characters exceeded

  • Jun 10, 2010 at 02:57 AM

    What was the error message number system popping up ??

    thanks

    G. Lakshmipathi

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jun 10, 2010 at 11:53 AM

    Hi Arup,

    Normally inbound delivery is created by using T code VL31N.

    Then you can do the GR against inbound delivery either using MIGO or MB0A.

    Hope this helps.

    Vivek

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jun 10, 2010 at 01:07 PM

    Hi Arup,

    Just follow the below mentioned step and it will resolve your problem

    Materials management->Pursache order >Set up stock transport order >Define Shipping Data for Plants-->

    Define customer no-. for plant

    Also go through the below link if you are using HU in your system

    http://arthur_ong.tripod.com/xmm015.htm

    I hope this help to you!

    Regards,

    KRishna O

    Edited by: Krishna O on Jun 10, 2010 3:09 PM

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jun 10, 2010 at 07:34 PM

    Hi Chandrashekhar,

    So here are things that I needed to clarify.

    1. I had configured the system in ECC 6.0 and did not enter any specifics for entries in Table T001W. I do not see entries in T001W in 4.6c either? Is it mandatory to have the entries in this table? ECC 6.0 had no issues whatsoever when using MIGO.

    2. No shipping conditions have been maintained.

    3. I am an ABAP programmer myself so I was curious to know if you had ever encountered this issue while looking at the above program that you have mentioned? I can debug the program but was wondering if there are some specifics that you have already encountered?

    Thanks,

    Arup

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Hello Arup

      No, I did not encounter the situation before and nor am I an ABAPer. I generally used concepts from issues I have faced in STOs related to Shipping data and some OSS notes I came across when I searched on your issue. Forget about point 1, but work on shipping conditions as that may help you. With respect to the program, I used 'where used' feature for the error message.

      Take a look at OSS note 490865 - Creating inbound deliveries from replenishment delivery

      This may not be relevant to your release but may throw some pointers.

  • avatar image
    Former Member
    Jun 11, 2010 at 03:55 PM

    Hey Chandrashekhar,

    I solved the particular problem. So the storage location had a handling unit requirement.

    So I set the HU requirements for storage locations HU Mgmt - Basics - MM - Inv Mgmt - Hu Reqmt for storage location and default values for deliveries.

    So here I set the partner storage location and also set the default customer and the partner storage location.

    Thanks for all the help. Hope this setting helps you with further configurations.

    Thanks.

    Arup

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Happy to hear. And will remember the tip. Did that program debugging or the OSS note help at all? Let me know. Thanks.

  • avatar image
    Former Member
    Jun 11, 2010 at 04:59 PM

    Well I did not go on to debug the program. Plain lazy I guess 😊

    Now I need to replicate the functionality for creating TO from TR using L_TO_CREATE_TR which presents me with problems in 4.6 c as I cannot decide to choose the Storage type at run time in 4.6c whereas I could do that in ECC 6.0.

    Add comment
    10|10000 characters needed characters exceeded