Skip to Content
avatar image
Former Member

Test Logon to SAP System failed during installation

Dear All

I am trying to install an ECC6.0 EHP 4 version using a system copy method. During my last step no. 26 - "Check DDIC password", I am facing a error message saying

"Test Logon to SAP system failed. SOLUTION: Make sure that the system is started, that the user DDIC exists and that the password of user DDIC is correct."

My instance is starting properly but however, i am not able to connect through SAP GUI as it gives error message

"SAP System Message : Program SAPMS380"

Checking the sapinst_dev.log, the final lines say

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:380]

CAbRfcImpl::setRfcConnectParam

RFC parameter CLIENT set to value 000.

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:380]

CAbRfcImpl::setRfcConnectParam

RFC parameter USER set to value DDIC.

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:380]

CAbRfcImpl::setRfcConnectParam

RFC parameter LCHECK set to value 1.

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:380]

CAbRfcImpl::setRfcConnectParam

RFC parameter PCS set to value 1.

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:380]

CAbRfcImpl::setRfcConnectParam

RFC parameter LANG set to value EN.

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:380]

CAbRfcImpl::setRfcConnectParam

RFC parameter ASHOST set to value scmserver.

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:380]

CAbRfcImpl::setRfcConnectParam

RFC parameter SYSNR set to value 10.

INFO 2010-05-18 09:16:03.154 [iaxxrfcimp.cpp:520]

CAbRfcImpl::checkConnectInfo

RFC connection information checked successfully.

WARNING[E] 2010-05-18 09:16:04.217 [iaxxrfcimp.cpp:433]

CAbRfcImpl::openRfcConn

FRF-00007 Unable to open RFC connection.

TRACE 2010-05-18 09:16:04.217 [iaxxrfcimp.cpp:434]

CAbRfcImpl::openRfcConn

Failed to open RFC connection

TRACE 2010-05-18 09:16:04.217 [iaxxrfcimp.cpp:436]

CAbRfcImpl::openRfcConn

Program SAPMSSY1 n

TRACE 2010-05-18 09:16:04.217 [iaxxgenimp.cpp:752]

CGuiEngineImp::showMessageBox

<html> <head> </head> <body> Test logon to SAP System IE6 failed. <p> SOLUTION: Make sure that the system is started, that the user DDIC exists and that the password of user DDIC is correct. </p> </body></html>

Please help

Regards

Lokesh Gupta

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

2 Answers

  • avatar image
    Former Member
    May 18, 2010 at 04:46 AM

    Hi,

    Probably, the password you used in installation step for DDIC is incorrect...

    Try to login in "Client 001" with user DDIC and use the Password of DDIC user of source system.

    If it fails, try with SAP* and password of source system.

    If this is also fails, then activate emergency SAP* user by adding the below parameter in INSTANCE profile at OS level.

    Edit the file /sapmnt/<SID>/profile/<SID>_DVEBMGS<NO>_<HOSTNAME>

    and add parameter

    login/no_automatic_user_sapstar = 0

    Restart SAP and login to "Client 001" and "Client 000" using SAP* and "pass" as password.

    Change the DDIC user password same as source system in both client "000" and "001".

    Then Retry the installation. It will go further...

    Regards.

    Rajesh Narkhede

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member Former Member

      Hi,

      If this is also fails, then activate emergency SAP* user by adding the below parameter in INSTANCE profile at OS level.

      Edit the file /sapmnt/<SID>/profile/<SID>_DVEBMGS<NO>_<HOSTNAME>

      and add parameter

      login/no_automatic_user_sapstar = 0

      Restart SAP and login to "Client 001" and "Client 000" using SAP* and "pass" as password.

      Change the DDIC user password same as source system in both client "000" and "001".

      Then Retry the installation. It will go further...

      Have you tried above steps (Activating Emergency User SAP*) ?

      REMEBER, YOU NEED TO RESTART THE SAP AFTER MODIFIED PROFILE PARAMETER...

      I hope, your database is up and running at this stage...

      Regards.

      Rajesh Narkhede

  • May 18, 2010 at 05:10 PM

    Hi,

    so you systemcopied a EHP4 system. One with Basis 7.01 ?

    What media did you use for that?

    Could it be, that you used the ERP 6.0 SR3 media?

    Your kernel might be wrong or too old then.

    Volker

    Add comment
    10|10000 characters needed characters exceeded