cancel
Showing results for 
Search instead for 
Did you mean: 

SXMB_MONI problem

Former Member
0 Kudos

Hi experts,

I am done file to file scenario i checked the Under component monitoring--> adapter monitoring --> Communication monitoring in this one it showing the status about receive and sender communication channels was successfully but the out put file was not created in the target directory. At the same time was checked in the SXMB_MONI but there it was showing only some components some more components are not available.

Available:

INBOUND MESSAGE

RECEIVER GROUPING

RESPONSE

Other than this we can't able to find the Runtime payload and all please can u help me out.

Regards,

-Prabhakar.A

Accepted Solutions (0)

Answers (4)

Answers (4)

former_member200962
Active Contributor
0 Kudos

This is just because your TRACE level has been set to 1 in SXMB_ADM --> Integration Engine COnfiguration.

raise it to at least 2 or at max 3

Regards,

Abhishek.

Former Member
0 Kudos

Hi,

Take the message id from Moni..and convert it to lowercase and search the same in MessagingSystem of adapter..

url for the same is http://host:port/MessagingSystem.

there search with the converted message id data...it will show you the detailed logs of the channel...

In order to enable more features in moni..activate the parameters Tracing and logging..as said..

HTH

Rajesh

former_member206760
Active Contributor
0 Kudos

may be the message is stuck in SMQ2/SMQ1

Former Member
0 Kudos

Hi Prabhakar,

1) make sure that your user ID has 777 (read,write,delete) access for the target directory.

2) Goto SXMB_ADM->Integration Engine Configuration->Specific config->Check whether parameters LOGGING,LOGGING_SYNC,TRACE_LEVEL under category RUNTIME are set or not....if not then set it.

Regds,

Pinangshuk.

Former Member
0 Kudos

Pinangshuk

1.I have all the rights.

2. But i can't able to find all these parameters under this *SXMB_ADM->Integration Engine Configuration->Specific config->Check whether parameters LOGGING,LOGGING_SYNC,TRACE_LEVEL under category RUNTIME.

I found only these parameters only in RUNTIME category ENGINE_TYPE and IS_RULE.

can u tell me required fields for the remaining. Current Value,Default value and all....

Regards,

-Prabhakar.A

former_member200962
Active Contributor
0 Kudos

Then this blog should help you: /people/michal.krawczyk2/blog/2005/05/10/xi-i-cannot-see-some-of-my-messages-in-the-sxmbmoni

Regards,

Abhishek.

Former Member
0 Kudos

Hi,

if it is already configured only then it will show...otherwise need to configure the same

click edit button and add those parameters..under runtime category...

HTH

Rajesh

Former Member
0 Kudos

Hi Experts,

I can not unable to find the solution for that still i can not find the remaining steps in SXMB_MONI.

Please can any one help me out.

Regards,

-Prabhakar.A

former_member200962
Active Contributor
0 Kudos

The blog given should help you out.....note one thing that you will get the message details for only those processings which were done after the parameters were included in SXMB_ADM........if you are assuming to see the message details of previously processed messages, then you wont be able to see.

Have you done the changes and activated cache?

Do not create multiple posts for same question!

Regards,

Abhishek.

Former Member
0 Kudos

Hi,

Follow the blog that has been given by Abhishek....you can see the current value there...default value will be 0...for TRACE_LEVEL default value is 1....you are not able to see the parameters means you dnt have authorization....take help from BASIS...they can do it...

Regds,

Pinangshuk.

Former Member
0 Kudos

Hi Abhishek,

Thanks for your help now it is working perfectly. I have one more problem all are successful but i can't able to find the Output file in the TARGET system. Can you tell me the solution.

Regards,

-Prabhakar.A

former_member200962
Active Contributor
0 Kudos
I have one more problem all are successful but i can't able to find the Output file in the TARGET system. 
Can you tell me the solution.

What is your channel saying? Is it indicating successful processing?

Former Member
0 Kudos

Hi,

Did you seen my first reply for finding out the process or logs..happened at receiver side for not generating the file in the target directory...

if not please check and follow the same and post if any errors found in that logs..

HTH

Rajesh

Former Member
0 Kudos

Hi,

Chk ur target directory name in receiver file channel is properly given or not...

Regds,

Pinangshuk.

Former Member
0 Kudos

HI,

It was showing successful. I checked in this one also http://host.port/MessagingSystem here also it is showing message was successfully delivered under received messages.

Regards,

-Prabhakar.A

Former Member
0 Kudos

Hi Prabhakar,

i think you are doing your first scenario, in your new PI server.

let me tell you certain brake points (trouble shooting)

1) Adapter level

2) moni level

3) Queue level

hope you succesfully come over above two points

check on Queus .. go to smq1 and smq2 --> check any queues exit..

if not go to SMQR tcode and register + activate your queus.. if already done , please send us your receiver adapter log ..

Note: search in SDN how to Register your Queus

Regards,

Pradeep A.

Former Member
0 Kudos

Hi Pradeep,

I checked on Queus .. go to smq1 and smq2 --> I can not found any queues here.. And i am not able to find any document for activating queues please can you tell me.

Regards,

-Prabhakar.A