cancel
Showing results for 
Search instead for 
Did you mean: 

Firefighter Configuration

Former Member
0 Kudos

Hi Experts,

For Firefighter configuration, do we need to define all the paramters with YES or NO value OR we can leave the one which we dont require, e.g "Assign FF Roles Instead of FF IDs" - we dont need this, so still do we need to make an entry for this paramater with value NO.

What is we define both the paramters "Send Log Report Execution Notification" and "Send Log Report Execution Notification Immediately" ?

FF reads CDHDR table for the changes, how can we find out which all changes would be covered in that - i mean does the RFC connection creation, deletion and change will be recorded ?

Thanks

Davinder

Accepted Solutions (0)

Answers (2)

Answers (2)

Former Member
0 Kudos

Thanks

Former Member
0 Kudos

Hello Davinder,

No, you do need to set all the parameters there. If you do not select these the default values will be taken into account.

First the data will be fetched from STAD and based on the entries available in STAD the corresponding change entries will be located in CDHDR. If the data does not exist in STAD then the corresponding entries will not be picked up from CDHDR as well.

I could not understand your question regarding "Send Log Report Execution Notification" and "Send Log Report Execution Notification Immediately" ? Can you please tell me more clearly.

Regards,

Varun

Former Member
0 Kudos

Appreciate Varun for your qucik answers.

No, you do need to set all the parameters there. If you do not select these the default values will be taken into account.

Does it mean default value is NO?

First the data will be fetched from STAD and based on the entries available in STAD the corresponding change entries will be located in CDHDR. If the data does not exist in STAD then the corresponding entries will not be picked up from CDHDR as well.

As per my understanding, first "RSCOLL00" should run and after that "/VIRSA/ZVFATBAK".

ok, so do we need to select the tables, programs, reports, etc which needs to be recorded in STAD ? Or everything happening in SAP system is being recorded automatically.

I

could not understand your question regarding "Send Log Report Execution Notification" and "Send Log Report Execution Notification Immediately" ? Can you please tell me more clearly

Sorry about that, i was trying to ask - what will happen if we define both parameters "Send Log Report Execution Notification" and "Send Log Report Execution Notification Immediately"

Once again Thanks.

Davinder

Former Member
0 Kudos

Hi Devinder,

Send Log Report Execution Notification" and "Send Log Report Execution Notification Immediately"

If you keep first one as yes then,your configured controler will get the notifiction regarding the changes made by the user in ECC thru assigned FF ID.Thru second one controler will recieve the login notification immediately after user login into assinged FF iD.I mean to say that there are two types of notifications,one is for changes made and the other one is for FF IDlogin info.

Regards,

Mukesh

Former Member
0 Kudos

Hello Davinder,

For the particular parameter you mentioned in this post "Assign FF Roles Instead of FF IDs" the default value is NO.

By default the table logging is ON for most of the tables but not all. For those tables for which table logging is not ON the data will not be captured in STAD and thus will not be fetched by firefighter.

You can contact your basis admin to check if table logging is ON for a particular table or not. If the operation you performed did not get captured in STAD then the table logging for that table might not

be active.

Regarding the 2 parameters "Send Log Report Execution Notification" and "Send Log Report Execution Notification Immediately" you can refer to the information available in the configuration guide of

AC5.3. Here is what these are all about:

1. Send Log Report Execution Notification - This parameter specifies whether log reports that contain information about Firefighter activity are emailed to controllers. If you set this to YES, then the report will be

sent to controller otherwise if you set this one to NO then the report will not be sent at all.

2. Send Log Report Execution Notification Immediately - This option specifies whether the log reports are sent to the controllers as soon as the background job (/VIRSA/ZVFATBAK) is executed or at

a predefined date and time. To send log report email notifications to the controller inboxes as soon as the /VIRSA/ZVFATBAK job runs, set

this parameter to Yes. If you plan to receive the job at regular intervals, schedule the job /VIRSA/ZVFAT_LOG_REPORT at regular intervals,

and set this parameter to No.

Regards,

Varun