Skip to Content
avatar image
Former Member

Planning run issue

Good morning,

I am planning a product in a sim version in APO, if I do a regen planning run it works but if I run the same scenario (and reset the results) with a net change it is not included (not planned) in the planning run.

Am I missing something obvious??

Thanks in advance.

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

6 Answers

  • Best Answer
    avatar image
    Former Member
    Jul 28, 2009 at 09:56 AM

    Hi UKuser,

    1) It may happen that the product view and background job will have two different

    heuristics selected, please check

    2) Check the job log and application logs during the time of job run.

    3) In background job, if you select entire planning horizon, then it will plan. In

    product view, it works based on SNP horizon

    4) Before u retry, delete the existing planned orders and retry

    Regards

    R. Senthil Mareeswaran.

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jul 18, 2009 at 03:39 PM

    Hi

    1. Check the Planning File entry SNP if the indicator is set (/sapapo/rrp_netch).

    2. Are you executing SNP Heuristic at MRP Area Level?

    Thanks,

    Sendil

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jul 16, 2009 at 09:52 AM

    Hi,

    I did not get you properly. Please check You have set the indicator to be able to run net change planning within the SNP heuristic. To check this Go to /sapapo/mvm.

    The indicator is only taken into account for the active planning version.

    Thanks,

    Satyajit

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jul 17, 2009 at 02:49 PM

    Hi UKuser,

    In netchange mode, it will give planning results only if you carry out planning relevant changes

    for the specified location product combination. The change should have been carried out

    after the previous planning run. If there is no change carried out for the combination after the

    previous run and if you execute net change run again, it will not give any results. This is

    standard functionality. Only in regen mode, the location product will be entirely planned

    again.

    Regards

    R. Senthil Mareeswaran.

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Hi Senthil,

      I am extremely sorry to interupt the conversation in between, but can you please tell me what exactly is meant by Regen Heu. .

      Does planning run taken with Location Heu or Network Heu means Regen heuristic ???

      Would be grateful to know your comments. .

      Thanks and Regards,

      Prasad.

  • avatar image
    Former Member
    Jul 21, 2009 at 07:27 AM

    Hi Prasad,

    Planning run can be performed both with netchange as well as with

    regenerative mode.

    Every time, when planning relevant changes are done in system, system

    automatically sets up planning file entry for the location product

    combination.

    If you select net change method, only those items with plannning file

    entries will be planned in planning run.

    If you select regen mode, the entire sequence will be replanned

    irrespective of planning file entries.

    Again, the selection of net change or regen mode is purely depends

    upon the client/business depending upon the requirement.

    Regards

    R. Senthil Mareeswaran.

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jul 28, 2009 at 09:01 AM

    Thanks for the input,

    If i run the heuristic in the product view (/sapapo/rrp3) APO will generate the required planned orders but if I leave it to the background planning run it does nothing.

    I have checked ECC to make sure the materials are in the planning file.

    Add comment
    10|10000 characters needed characters exceeded