Skip to Content
avatar image
Former Member

RESULT RECORDING PROBLEM

Dear Gurus,

I am facing problem I have maintained formula for paricular MIC,e.g Zn-for this MIC i have to calculate the percantage as 100 minus balance of the remaining MICs eg i have maintained in this form--1

100-(C9010C9020C9030C9040C9050C9060C9070C9080C9090)

Please note i have maintain the folowing parameters in control indicators for the MICs from 10 to 90 in the Inspection plan

1) Sampling procedure

2) Required chara

3) single results

4) Fixed scope

5)Record measured values

6)print

7) documentation

and only for the MIC which formula is maintain i have maintained CAL CHAR.

when i creat a purchase and do migo an inpsection lot is gnerated.

when go to t.code QA32 to record results in RECORD RESULTS CHARACTERISTICS OVERVIEW

I HAVE NOTICED THE FOLLOWING PROBLEMS

1) FORMULA IS NOT BEEN CALCULATED.

2)INSPECTED COLCUMN NEXT TO SINGLE VALUE IS AN INPUT SCREEN.i.E-Number of Inspected Sample Units--(WHAT I MEAN ITS NOT GREY FEILD-THE VALUES HERE SHOULD BE 1 AND GREY )

3)ALSO THE SINGLE VALUE TAB IS GREY NOT USUAL-IF CLICK ON IT THE TAB DROP DOWN.

I HAVE RUN THIS SCENRIO IN MY DEVELOPMENT SERVER AND IT WORKED PREFECTLY,BUT MY CLIENT SERVER I AM GETTING THIS PROBLEM

WHAT ARE SETTING I AM MISSING.

Regards

Ram

Edited by: RAMKUMAR WARIYAR on Feb 24, 2009 4:41 PM

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

2 Answers

  • Best Answer
    Feb 25, 2009 at 08:25 AM

    Dear Ram

    1) As the sample size was 1 system was taking this as Summarised recording & that is the reason why the system is showing 3 tabs instead 4

    2) Please do the following setting in Config : SPRO>QM> Basic Setting> maintain setting for plant level>Plant> Result recording > untick Summ. Recording n=1.

    If you had ticked this means that the results recording will always be summarized if n = 1 (for example when inspecting one unit or 1 ml).

    please do check now whether the formula is working for a new lot and you have 4 tabs in RR

    Was a good question to solve

    Regards

    gajesh

    Add comment
    10|10000 characters needed characters exceeded

  • Feb 25, 2009 at 05:31 AM

    Dear Ram

    It seems to me you have selected in the Control indicator of the mic may be summarised recording. You might have selected single recording for all but for the formula MIC

    if you have selected Summarised recording then

    1)Formula will not get calculated if control indicator or sampling procedure is different for Calc MIC

    2) inspected column will be open for inputting the inspected values

    3)Single value drop down will not be active

    please check thoroghly

    Regards

    gajesh

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Dear Gajesh,

      Thanks for the reply,

      I have checked all parameters you have told me check,

      I have total 10 MIC in the inspection paln.for all 10 i have maintained

      1) Single Results

      2) Same sampling procedure and sample size 1

      3) only for 10th MIC for which i have maintained single results and calcu chara.

      Even i have created another dummy material and created in inspection plan for that material,but i getting the same problem,thats as you said summizarised recording.

      NOTE: In the Result Recording overview screen,i am getting only 3 tabs

      1) General

      2) Summarized

      3) Indicators

      Whereas there should 4 tabs,Unit to be inspected tab is not there.

      In indicators Tab tick is there in summarized recording colcumn and measured values

      What seetings have i missed out

      Regards

      Ram