cancel
Showing results for 
Search instead for 
Did you mean: 

Error message for the T Code VL02N

Former Member
0 Kudos

Good morning gurus,

I have this poblem with the transaction VL02N : when I try to launch an outbound delivery, I get this message: "Item to be picked by WM picking quantity cannot be entered)".

FYI, I enter the stock location and the picking quantity manually.

Thanks for your help!!!

Accepted Solutions (1)

Accepted Solutions (1)

Former Member
0 Kudos

Hi,

probably your storage location is linked to a Warehouse number.

You must create a transfer order for picking and confirm it.

In VL02N:

Subsequent functions / Create transfer order

Bye

Former Member
0 Kudos

Hello,

I've already tried this using the transaction LT03 but I get the following error message :"No items that are to be picked were found".

Where else could the problem be??

Thank you

csaba_szommer
Active Contributor
0 Kudos

Hi,

Please go into the delivery and check the picked qty (picking tab), picking status and WM status ion "Processing" tab (item level).

What can you see?

Is your storage location assigned to a WH?

Is something running in the background when you post GI? I'm asking this because you mentioned that you get the error message when you wanted to post the GI.

Please also provide the number (ID) of the error messages it might be helpful.

Regards,

Csaba

Former Member
0 Kudos

Hi,

Plase find below the description of the items you asked about :

In the picking tab : Picked quantity (entered manually) is equal to delivery quantity (which is available in stock as appearent in MMBE)

In Processing tab : Picking - C - fully picked

WM status - - No WM trnsf ord reqd

As for the storage location, it is assigned to a WH and nothing is running in the background.

The ID of the error message is VL118. In case it might be useful, here is what it says in detail :

Diagnosis

For this item, picking is carried out using warehouse management

transfer orders since the material is stored in a warehouse with random

storage.

System response

The system does not allow you to enter a picking quantity manually. The

picking quantity is copied automatically into the delivery during the

creation of the corresponding transfer order.

Regards,

Houda

csaba_szommer
Active Contributor
0 Kudos

Hi,

In the picking tab : Picked quantity (entered manually) is equal to delivery quantity (which is available in stock as appearent in MMBE)

In Processing tab : Picking - C - fully picked

WM status - - No WM trnsf ord reqd

As for the storage location, it is assigned to a WH and nothing is running in the background.

Thi is very strange to me...

You said that SLoc assigned to a WH and you also said that WM status is "No WM trnsf ord reqd" (VBUP-LVSTA, in our system the text is "Not relevant" for this field if it is empty).

Since your SLoc is asigned to a WH I cannot understand why this status says it's not WM relevant.

If the item would be WM relevant (normally) you would have been not bale to input the picked qty manually...

My further questions:

- Does your material has WM view (for the WH that is assigned to the Plant/Sloc combination)?

- Can you see stock in LX02 for your material (under the SLoc, transaction code LX02)? What can you see in MB52 for the same SLoc? Are the reports in harmony?

- Are you facing the same error if you create a new delivery with the same item where the delivering Plant is the same as well as the SLoc?

- Delete the picked qty and change the SLoc to a non-WM managed SLoc > after that input again the SLoc that is assigned to th WH. What happens (WM status should appear, and picked qtry field should get disabled for manual input)?

I've checked OSS notes, there's only two in connection with this error message, none of them cover your problem (755559, 132767).

Regards,

Csaba

Edited by: Csaba Szommer on Jan 27, 2009 7:52 PM

Former Member
0 Kudos

Hello,

Actually, I went back to your first answer and went through the process by using the Tcode LT03. It was actually the key to the problem.

Thanks a lot

Houda

Former Member
0 Kudos

Houda,

Please check the 'item category' setting. Is the item category you using 'relevant for picking'? This is a check at 'Item Category' level which needs to be set up. Go to IMG- LE- Shipping-Deliveries-Define Item Category and for your item category in the delivery check if it made relevant for picking.

Good luck!!

Former Member
0 Kudos

Hi Houda,

can you please let me know how were you able to fix the problem via LT03 for this error message. I'm getting the error mesage when i'm in LT03. No items that are to be picked were found".

Thnaks

Anusha

Edited by: anusha vemulapati on Aug 9, 2011 1:05 AM

Answers (0)