on 01-15-2009 5:25 AM
Hi,
As there are some changes in the Sources to make that to in phase I have added same fields to BW also.These are all updated in the extract structure as well.But when I tried to INIT again for the ODS I am getting an error message and the INIT is happening.Can any one help how to figurre out this.
points will be definitely assigned.
Thanks,
Vasu
Hi,
Replicate the data source, activate the transfer structure and than try...it should work...
Regards
Prasad Nannuri
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Now I got a different message in the SM 37 for this job.I have pasted the message.
Job started
Step 001 started (program RSBATCH1, variant &0000000001112, user ID xyz)
Start InfoPackage ZPAK_4C713GY9Z7OU865MTR8JD4VB4
InfoPackage ZPAK_4C713GY9Z7OU865MTR8JD4VB4 created request REQU_4CI88A7G3L10LVC9ABNAE3QTC
Job finished
HI,
that mean the job was succesful and not the job in R/3 is schedule....or...... look for the job in R/3 and where if its failing or not.
check the user ID for ALEREMOTE in R/3 and see if you see any jobs for today and inside the job log check for your data source...it will tell you why its failing or if its finished or not.
If nothing sloves then try to activate the extract structure again....and the data source again as well and replicate it again in BW.
try to use the program RSDS_DATASOURCE_ACTIVATE_ALL in BW to make sure the data source is activated in BW as well and then try to schedule the data load.
Thanks
Ajeet
Hi
Recheck your entire Flow on R/3 Side again, as the Job says that your BI Job process has been started and finished without reaching on R/3 Side.
Establish/Test/Activate the Connection between the systems. Replicate the Data sources and Try to activate the Entire Flow again with relevant mappings.
And try to Upload the Data.
Hope it helps and clear
Hi,
Check in SM37 in Sourcesystem if it fails in SS then find cause might be the table sapce issue in SS.
Regards,
Satya
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
HI,
Can you eloborate the statement so that i can understand.
Regards,
Shashikanth.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
There are newly added field in the data source so to accomodiate that changes in phase I added fields in the communication structure and also mapped in the transfer structure and it is one to one.As there was allready an INTI for that ODS so to check whether these new fields are also getting populated are not I have again made an INIT for that ODS but this INIT got failed.Below is the status what I am getting
Job started
Step 001 started (program RSBATCH1, variant &0000000001111, user ID xyz)
Start InfoPackage ZPAK_4C713GY9Z7OU865MTR8JD4VB4
Transfer Rule(s) ZODS_BI vated
InfoPackage ZPAK_4C713GY9Z7OU865MTR8JD4VB4 created request REQU_4CI7HFUF87Y03YFN7S4PG9GN4
Job finished
Hope this is enough.
User | Count |
---|---|
101 | |
13 | |
13 | |
11 | |
11 | |
7 | |
6 | |
5 | |
4 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.