Skip to Content

SAP Language Installation Issue while import language part for support package

May 10 at 09:25 AM


avatar image
Former Member

Hi Expert's

Recently , we have request for FR language installation in our ERP 6.0 system

which was already upgraded to EHP7 ERP 6.0 SP12

- For language installation , we have used lower base version (i.e) ERP 6.0

and import transport job in SMLT was completed successful without any issue

- For Post steps , import language part of support package ,we are getting too many component missing then we have realized its due to EH7 upgrade component missing

so we have not proceed further

Per sap note 330104 - Transport requests used for language delivery // SRx

we have found required patch file

My question is :

Can i do the import again in SMLT with new versions patch file ?

10 |10000 characters needed characters left characters exceeded
* Please Login or Register to Answer, Follow or Comment.

2 Answers

Andreas Lichtenau
May 11 at 06:09 AM

Hi Decio,

yes, you can simply install the language again.
If you need further help you can also check the official SAP Language Installation WIKI at "".


Show 6 Share
10 |10000 characters needed characters left characters exceeded
Former Member

Hi Andreas,

Thanks for your reply,

let me try


Former Member

Hi ,

while i'm trying to import again facing issue during phase "create versions before import" in one pacakage alone

As per sap note 1929147 - ITAB_DUPLICATE_KEY error during language installation ,we have remove duplicate key entry

but still we are facing duplicate key issue as similar as note mentioned

we could observe same duplicate key 0EA7B9B6BB9AD411955D0060B03C6B76 in our ST22 dump

any advice or guidance would be greatly appreciated


Hi Decio,

you've mentioned that you've checked the following SAP note: 1929147.

Can you confirm that you've followed also the instructions from SAP Note 1617634?
Perhaps there is a buffer issue. Please reset them according to SAP Note 26171.

If this is not working I think someone of SAP Support has to check it on the system.

Best regards,

Former Member

Hi Andreas,

Yes .. I have followed the SAP Note 1617634 and ran the report Z_MIME_DUPLICATES_DELETE ( with/ without test_mode ) . I have used flags for TEST_RUN and LANG_DUP only (not tried any other option )

ST22 dump details:

Category ABAP Programming Error
Application Component BC-SRV-KPR-DMS

|Error analysis |
| An attempt was made to insert an entry into table |
| Updating |
| unique table key "PRIMARY_KEY" resulted in a duplicate entry however. The key |
| in |
| question could be either the primary key or a secondary key. |
| |
| The key components of the duplicate entry have the values |
| "{0EA7B9B6BB9AD411955D0060B03C6B76}" " " " "

|How to correct the error |
| Probably the only way to eliminate the error is to correct the program. |
| - |
| If the error occurs in a non-modfied SAP program, you might be able to |
| find a solution in the SAP Notes system. If you have access to the SAP |
| Notes system, check there first using the following keywords: |
| |
| "SAPLSDCL" bzw. LSDCLU56 |
| If you cannot solve the problem yourself, please send the following |
| information to SAP:


Former Member

I have also tried with other option in Z_MIME_DUPLICATES_DELETE report ( test_mode )

- its show some duplicate entry but none of them matched with st22 dump key


so I haven't execute in change_mode


Hi Decio,

can you please contact the support on component BC-SRV-KPR-DMF? This has to be checked on the system.


Han Liu
Jun 14 at 02:59 AM

Hi Former

You can refer below Note for language isntall and language supplementation.

1935497 - How to finish a language import by SMLT

1156507 - Language supplementation, RSREFILL and client maintenance

If you meet detail error message in transaction code SLMT, you can open an incident to component BC-CTS-LAN for further further.

Best Regards,


10 |10000 characters needed characters left characters exceeded