on 06-05-2008 8:06 AM
Dear Sir,
In MD04 Inspection lot number displayed.
In QA32 it displayed also with red signal.
Status shows REL CALC SPRQ ORRQ.
In QA32 Informaion message displayed charactristics results can not be recorded for inspection lot xxxxxxxxx
But when I wants to do Results recording in QE51N. System displays entry is not displayed.
Please suggest the required settings to create req. lot in QE51N
points will be rewarded........
Hi,
Unless unitill the status of your insepction lot become REL........., that will not get displayed in QE51N.
To change the status REL , you need to
1. assign the task list to the lot.
2. and calculate the sample for it if applicable.
As soon as you complete above metnioned steps your lot status will cahnged to REL........ and will display in QE51N also.
Best Of Luck.
Regards,
Dhaval
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Dear Sachin,
All of above pls let us know, when you execute the QE51N, what is happing. the lot is appearing and then it becomes un-operatable?? or it is not appearing even?
If it is not appearing then check,,,
1. The other fields in QE51n, means plant, dates,btach etc..
2. Check the details for your insepction lot.
And it is getting open and then it shows any error then.
If once the lot shows REL status then it normaly opens in QE51N.
First of all pls let us know the entire status of your lot, if it is changed from "CRTD CHCR SPRQ" to "REL CALC SPRQ". Means your task list is based on inspection point "Physical Sample". Check it in the header in your task list. Field Inspection point. In this case you need to manually release the phaysical samples also, (that again depend up on your sampling procedure).
So pls let us know the correct status of the lot.
Update us to help you more, reward points to help you better!
Regards,.
Shyamal
Hi Sachin
In the selection screen, take away the content in the field "Maximum no. of hits". The functionality behind this field is doubtful. If you have a lot of open inspection lots, and you limit the search to what should be a few hits, you still may not find these in your worklist, becasue of the restriction in this field, which is 50 as standard.
Regards
Jan Erik
Hi Sachin..,
Please check whether inspection plan is assigned to your lot or not.
if not go to inspection lot in change mode and reasign inspection plan.
regards.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
try to do the result recording through QA32 only.
Regards
Amit Parkhi
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Sir,
In QA32 it displayed also with red signal.
Status shows REL CALC SPRQ ORRQ.
In QA32 Information message displayed charactristics results can not be recorded for inspection lot xxxxxxxxx
Message gives the information you can not record any characteristics results for this inspection lt.
The material master has not been set up for the existing inspection type in such away that results recording is not supported
please suggest the further setting.......
Sir,
In QA32 it displayed also with red signal.
Status shows REL CALC SPRQ ORRQ.
In QA32 Information message displayed charactristics results can not be recorded for inspection lot xxxxxxxxx
Message gives the information you can not record any characteristics results for this inspection lt.
The material master has not been set up for the existing inspection type in such away that results recording is not supported
please suggest the further setting.......
User | Count |
---|---|
88 | |
7 | |
6 | |
4 | |
3 | |
3 | |
3 | |
3 | |
3 | |
3 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.