Skip to Content
avatar image
Former Member

aknowledgement error in moni

hai iam configured one idoc to file senario up to yester day it is working fain but today it is geving some problem

sxmb_mini it showing success but it is not creating faile at destination folder and

at acknowledge status it is showing

Still awaiting acknowledgment

what may be the probs

pls help me

with regards

srikanth vipparla

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

6 Answers

  • May 22, 2008 at 09:22 AM

    Hi,

    you need to make an entry in table IDXNOALE for your IDOC message type to stop the IDOC ack. request.

    Have a look at the section "Switching Off ALE audit messages" of the below blog

    /people/saravanakumar.kuppusamy2/blog/2005/01/20/configuration-tips-for-a-business-serviceintegration-process-to-send-back-ale-audit-idoc

    Note: IDoc technology supports its own acknowledgment technology, namely the ALE Audit. Here there are no acknowledgment requests from the sender. Instead, the receiver decides whether an acknowledgment IDoc should be sent back to the sender based on the ALE configuration. These acknowledgment IDocs are only used for monitoring on the sender side.

    IDoc technology is the only technology in which positive acknowledgments from the application contain data. This data is sent by the IDoc adapter in an acknowledgment IDoc if the sender is an IDoc system. Otherwise, the data is discarded.

    For the inbound IDoc adapter to be able to send an acknowledgment IDoc to the sender, a communication channel with the interface ALEAUD.ALEAUD01 must be maintained for the sender.

    Regards

    Aashish Sinha

    PS : reward points if helpful

    Edited by: Aashish Sinha on May 22, 2008 11:23 AM

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    May 22, 2008 at 09:29 AM

    HI,

    The same problem has been solved in threads mentioned below.

    Idoc to File Scenario

    unwanted ack idocs

    Also check this link for ur future reference

    http://help.sap.com/saphelp_nw04/helpdata/en/6a/e6194119d8f323e10000000a155106/content.htm

    reward points if u found it useful 😊

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    May 22, 2008 at 09:32 AM

    success status in sxmb_moni only tells you that the message has been passed to the adapter engine successfully. The message is likely stuck in the adapter engine . Check the adapter and adapter engine monitor in RWB.

    For the adapter monitor, within RWB, goto Component Monitoring, select your AE, and look for Adapter Monitor button. Then drill down til you find your specific FTP receiver channel for a status and potential problems.

    Note: reward points if solution found helpfull

    Regards

    Chandrakanth.k

    Add comment
    10|10000 characters needed characters exceeded

  • May 22, 2008 at 09:55 AM

    Hi Srikanth,

    You get that message because it is waiting for an acknowledgement and if you donot need that you need to supress it.

    so, try to maintain the table IDXNOALE , but still its not working .

    May be am not maintaining the table IDXNOALE correctly . Any idea or further hints here ?

    I solved a similar thread sometime back, please see my replies to that thread,

    unwanted ack idocs

    The steps are also in the doc:

    http://sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/xi/xi-how-to-guides/how%20to%20handle%20acknowledgments%20for%20idoc.pdf

    This pdf gets you the steps.

    Reward points if this helps

    Regards

    Pragathi.

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    May 22, 2008 at 09:55 AM

    HI Srikanth

    This is not a big issue. Only thing is that you might have configrured the acknowledgement for IDOC. U might have configured ALEAUIT.

    For supressing the acknowledgement you have to follow following steps

    1) Call transaction SE38, and run program IDX_NOALE.

    2) Specify Sender Port, and Sender Client.

    3) Choose either Request Acknowledgment or Do Not Request

    Acknowledgment

    For more help see this

    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/903a0abc-e56e-2910-51a8-9dc616df56eb

    Regards

    Abhishek Mahajan

    **Rewards Points if helpful**

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    May 22, 2008 at 10:03 AM

    Hi Srikanth,

    Once File is reached target folder the acknowledgement status is showing.

    but u can say the file not reached to target folder. so check it message monitoring in the RWB of the message status or check it MDT(Message Display tool).

    Regards,

    Sateesh

    Add comment
    10|10000 characters needed characters exceeded