Skip to Content
author's profile photo Former Member
Former Member

Forecast release from DP to R/3

Dear Experts,

Could any please replay me for the below issue

I have released Net forecast from DP to R/3 for a particular product and I found message in job log as "Successful transfer to R/3". But there is no forecast figures in MD62 or MD63.

what might be the reason behind that?

Thank you

Add a comment
10|10000 characters needed characters exceeded

Related questions

6 Answers

  • Best Answer
    author's profile photo Former Member
    Former Member
    Posted on Dec 02, 2007 at 12:11 PM

    Hi Sriramulu,

    Following are the points that you have to consider while releasing the data to R/3 from DP.

    Checks in APO

    1. Product and location should exist in APO.

    2. Planning Book/Data view should have a Time bucket profile with one periodicty

    3. Distribution defination should be setup on APO. the following is the path to set this.

    SPRO > IMG > Advanced Planning and Optimization --> Basic Settings --> Integration --> Publication -->Maintain Distribution Defination

    Specify "Planned Independent Requirement" and the location(Plant) for which you are transfering PIR and logical system.

    Checks in R/3.

    1. MRP Type in Material Master should be X0 (MRP1 View)

    Best Regards.

    Raghu Kishore

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Nov 30, 2007 at 01:25 PM

    Hi ,

    I hope you have done all the Prerequisite settings as below :

    .have set up your products in SAP APO

    .have set up your locations in SAP APO

    ·have created a data view for this task in SAP APO.with

    ¬° future planning horizon only

    ii planning buckets profile with one periodicity only

    iii Only the key figure(s) that you want to transfer to SAP R/3

    .have set the planning strategy of each material in SAP R/3.

    This should transfer the data without errors and also please check the same in MD04 if you can see it there..

    Regards ,

    Digambar

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Nov 30, 2007 at 01:36 PM

    Also check in MD74

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Nov 30, 2007 at 02:06 PM

    I think you need also to maintain the "Maintain Distribution Definition" per location in SPRO!

    Gave me a headache several times...

    Regards

    Stefan

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Nov 30, 2007 at 06:03 PM

    Sriramulu-

    there might be couple of issues

    1) have you set up the publication rules for transfer of PIR? if not then try to take a look into that by using SPRO (has to be set up for each location)

    2) check the RFC destinations and user passwords that might have expired.if yes then reset it.

    Regards

    Suresh Garg

    Message was edited by:

    Suresh Garg

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Dec 02, 2007 at 03:55 AM

    Please also check whether product, location exist in APO as master data.

    Add a comment
    10|10000 characters needed characters exceeded

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.