cancel
Showing results for 
Search instead for 
Did you mean: 

IDOC testing

former_member240483
Contributor
0 Kudos

Hi there,

I am trying test IDOC to IDOC interface.

WE19 and clicked standard outbound processing it is giving a message"Port doesnot exist in the table of port discription..

what is this error i am using ORDERS.ORDRS04 IDOC...

Regards

Rao

Accepted Solutions (0)

Answers (3)

Answers (3)

former_member614185
Contributor
0 Kudos

Maintain Logical system, port in the control record goto edit-->control record

former_member614185
Contributor
0 Kudos

Hi,

In WE19.

Do the following steps

From menu IDOC --> EDIT CONTROL RECORD

Maintain sender and receiver port, partner no.,partner type.

And IDoc Message type.

now Do standard outbound processing.

former_member240483
Contributor
0 Kudos

Thnaks Prabhu,

i did like as u said but it is saying IDOC create d but not sent and it is saved...

Regards

Rao

nisarkhan_n
Active Contributor
0 Kudos

y dnt you rerun the IDOC with proper control record as suggested by MR. PRABHU

prateek
Active Contributor
0 Kudos

What is the status of ur idoc?

And have u checked the port at R3 for XI using we21.

Regards,

Prateek

former_member240483
Contributor
0 Kudos

Yes i do checked the port at R3 it is ok...but idoc saying cannot or couldnot be sent dioc...

Former Member
0 Kudos

go into the transaction to send it, and type /h into the transaction bar and debug it...

nisarkhan_n
Active Contributor
0 Kudos

pls post the error descrition in detail (sm58)

former_member240483
Contributor
0 Kudos

I didnt put source LS name in Target systems ...is this may be cause for this prob....

Regards

Rao

nisarkhan_n
Active Contributor
0 Kudos

you mean you ahve created the Partner profile but not lsited the LS name in SALE? try entering that.....but the problem is that it is not accepting the Port right? pls post the error step (what error you c in sxmb_moni) and in the sm58 is any

Message was edited by:

n Khan

former_member240483
Contributor
0 Kudos

yes,i created ports on both sides and it seems allright? i am not sure why IDOC in not going.

nisarkhan_n
Active Contributor
0 Kudos

can you list down the steps which you have done and how youa re triggering the IDOC...actual interface flow if you can

former_member240483
Contributor
0 Kudos

Hi Khna,

My interface is.

R3(A)---PI--


R3(A) (means source and targets are same R3 systems).

R3(A) system pushes the IDOC Through PI it reaches the R3(A).

I created:

R3(A):

RFC destination(for PI)

Port(of PI)

Partner profiles.

PI:

RFC destination(for R3(A))

Port(of R3(A))

Partner profiles.

Created one CC at reciver for R3(A) system....

Regards

Rao

prateek
Active Contributor
0 Kudos

Recheck ur Logical system names for the client on which u r sending the idoc. And as I asked u before, please check and confirm the status of ur idoc in we02

Regards,

Prateek

nisarkhan_n
Active Contributor
0 Kudos

so wehn you send the IDOC fro the sender R/3 it is giving error as in your first post...or while receing the idoc?

when you try to push from the R/3 to PI ( port which you have created is pointig to XI) it is not entering SXMB_MONI?

what's the status of IDOC?

former_member240483
Contributor
0 Kudos

status code is 37...

nisarkhan_n
Active Contributor
0 Kudos

open the idoc control record in tcode: WE19, and check if the partner informations are correct. Open transaction WE20 and check if your system can send the idoc type to the specified receiver partner.

/people/sameer.shadab/blog/2005/07/25/reposting-idocs-instead-of-recreating--for-testing-purpose-xi( check thismight be helpfull)

prateek
Active Contributor
0 Kudos

That means u could have the following problems

1. The control record not filled properly

Sender, reciver name

Port / Message Type

2. The data u r passing is incorrect. Please find all details in we60

Regards,

Prateek

former_member240483
Contributor
0 Kudos

I double checked ports,partner profiles,RFC destinations looks allright.

nisarkhan_n
Active Contributor
0 Kudos

are you sure you hsve specified the trfc port pointing to XI.....just check one more time...it is not recognixing the port which you have entred

Former Member
0 Kudos

Has IDX1 and WE21 been configured?