04-09-2007 1:35 PM
Please can you help me how to go debug mode in program.
I want to do debugging,please help me.
Tell me the procedure.
Thanks & Regards
04-09-2007 1:40 PM
Hi Ali,
Hi Put a breakl point in the program and run it, it will stop the program when the statment comes. or else you can write BREAK-POINT in the code, it will also stops the processing when the control see the break point
http://www.saplinks.net/index.php?option=com_content&task=view&id=24&Itemid=34
Look at the SAP help link below
http://help.sap.com/saphelp_nw2004s/helpdata/en/c6/617ca9e68c11d2b2ab080009b43351/content.htm
Regards
Sudheer
04-09-2007 1:38 PM
hi Ali,
Refer to this thread
http://help.sap.com/saphelp_47x200/helpdata/en/c6/617ca9e68c11d2b2ab080009b43351/content.htm
Regards,
Santosh
04-09-2007 1:38 PM
Hi Ali,
Check these documents.
http://www.cba.nau.edu/haney-j/CIS497/Assignments/Debugging.doc
http://help.sap.com/saphelp_nw04/helpdata/en/5a/4ed93f130f9215e10000000a155106/frameset.htm
http://help.sap.com/saphelp_47x200/helpdata/en/c6/617ca9e68c11d2b2ab080009b43351/content.htm
http://www.cba.nau.edu/haney-j/CIS497/Assignments/Debugging.doc
http://help.sap.com/saphelp_erp2005/helpdata/en/b3/d322540c3beb4ba53795784eebb680/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/84/1f624f4505144199e3d570cf7a9225/frameset.htm
http://help.sap.com/saphelp_bw30b/helpdata/en/c6/617ca9e68c11d2b2ab080009b43351/content.htm
http://help.sap.com/saphelp_erp2005/helpdata/en/b3/d322540c3beb4ba53795784eebb680/frameset.htm
Hope this resolves your query.
Reward all the helpful answers.
Regards
04-09-2007 1:40 PM
Hi Ali,
Hi Put a breakl point in the program and run it, it will stop the program when the statment comes. or else you can write BREAK-POINT in the code, it will also stops the processing when the control see the break point
http://www.saplinks.net/index.php?option=com_content&task=view&id=24&Itemid=34
Look at the SAP help link below
http://help.sap.com/saphelp_nw2004s/helpdata/en/c6/617ca9e68c11d2b2ab080009b43351/content.htm
Regards
Sudheer
04-09-2007 1:41 PM
Hi,
There are 3 ways to enter into debug mode
write BREAK-POINT in the code and execute it will stop. (hard break point)
second keep a soft break point from the Ediotr MENU (red Button) on a line and execute it stoops there during execution.
Or execute the program, enter /h in the command, then again press F8. it goes into debugging mode and goes line by line.
For line by line debug press F5.
to skip the aprticular routine or perform press F6
to execute press F 8.
To keep the watch point. define the condition and execute it stops at that condition point.
then by pressing F5,F6 and F8 you can debug the relavent code
reward if useful
regards,
ANJI
04-09-2007 1:41 PM
Hi Ali,
Before executing the program give /H in the transaction code area and press enter. After that you execute the program.
Regards
SG