Skip to Content
author's profile photo Former Member
Former Member

Process chain not stating subsequent job

We are on NW04s and while process chains does not kick off next job even though the previous job completes sucessfully and the process is Green.

We do not use DTP process to load data.

Thanks

Add a comment
10|10000 characters needed characters exceeded

Related questions

7 Answers

  • Best Answer
    author's profile photo Former Member
    Former Member
    Posted on Feb 20, 2007 at 05:10 PM

    We are on SP 11 the processes are linked with always.

    Thanks

    Add a comment
    10|10000 characters needed characters exceeded

    • Former Member Former Member

      Well here could be the catch..

      Have a look below from the OSS -914305 (SP -11)

      In very quick parallel asynchronous processes, even though one or more processes may be successful, the process chain log may not contain any instances. As a result, the chain does not continue after the successful process. Note 994007 causes this error. For further information, refer to Notes 1005481 and 1003941.

      Hope it Helps

      Chetan

      @CP..

  • Posted on Feb 20, 2007 at 04:46 PM

    Hi Unni,

    Try to activate the chain once more and then execute it.

    Hope this helps...

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Feb 20, 2007 at 04:54 PM

    Treid that multiple times, the behaviour is not consistent it happens in multiple chains and sometimes goes through with out any problem, and the even when it stops it stops at different process.

    Thanks

    Sajith

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Feb 20, 2007 at 05:04 PM

    which SP are you on for NW2004s.

    Whats the event linked between two process types - sucess or failure ,always ??

    does your PC stops even if the event is "always""

    Hope it Helps

    Chetan

    @CP..

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Feb 20, 2007 at 05:22 PM

    This is observed in bigger chains and restriced to a couple of them, these chains were not created in 04S but upgraded from NW04. As I mentioned earlier this is not consistent.

    Thanks

    Add a comment
    10|10000 characters needed characters exceeded

    • Former Member

      did you read my previous post..

      here it is again..

      It talks abt applying sp-12 or apply advance corrections from that note.

      Well here could be the catch..

      Have a look below from the OSS -914305 (SP -11)

      In very quick parallel asynchronous processes, even though one or more processes may be successful, the process chain log may not contain any instances. As a result, the chain does not continue after the successful process. Note 994007 causes this error. For further information, refer to Notes 1005481 and 1003941.

      Hope it Helps

      Chetan

      @CP..

  • author's profile photo Former Member
    Former Member
    Posted on Feb 20, 2007 at 05:30 PM

    CP, Looks like the notes you pointed addresses the same issue, I will update after reviewing and applying notes and testing it.

    Thanks

    Sajith

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Apr 26, 2007 at 04:34 PM

    Hi,

    We are having this problem with SP10 and we are planning to apply SP11 in few days. Does it mean when we apply SP11 the problem will get resolved or do we have to apply Notes 1005481 and 1003941 on top of SP11.

    Please clarify.

    Thanks

    Gopa

    Add a comment
    10|10000 characters needed characters exceeded

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.