on 01-31-2007 8:42 AM
Hey guys
can anyone help me with setting up values in Control record for an IDOC to File scenario.
my configuration is as below
On R/3 Side
RFC destination(SM59) - SAPXI
Logical System(BD54) - SAP_IDOC
Port to XI(WE21) - P_SAP_IDOC
Partner Profile(use LS created in WE20) - SAP_IDOC
On XI side
RFC Destination(SM59) - SAPR3
Port to R/3(IDX1) - XI2R3
Please give me the values i need to put into my control record,everytime i m getting error 37 in WE02
thanx
ahmad
Hi,
as you said ,network prob.
Check the IDoc data correctly.. ,
did you mapped any thing in EDI_DC40 control record ..
Regards.
Chilla..
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hey guys
i m still struggling with posting the IDOC from R/3 to XI for my IDOC-XI-File scenario.below is the configuration i have done.can anyone provide me all the entries i need to make in WE19,control structure.
On R/3 Side
RFC destination(SM59) - SAPXI
Logical System(BD54) - SAP_IDOC
Port to XI(WE21) - P_SAP_IDOC
Partner Profile(use LS created in WE20) - SAP_IDOC
On XI side
RFC Destination(SM59) - SAPR3
Port to R/3(IDX1) - XI2R3
R/3 system ID: EI3
R/3 Client :800
XI system ID: NXI
XI Client: 400
In SLD
Business System: BS_IDOC_file (using logical system EI3CLNT800).
as i m doing this just as a test scenario,i m mapping only one value (Title ) from IDOC to my file structure.
i m unable to push the IDOC from R/3.
can anyone provide me with all the entries i need to make in my control structure.
thanx
ahmad
Message was edited by:
Ahmad
Hi Ahmad,
The Port created in IDX1 should be named as SAPEI3 as suggested in SAP help link http://help.sap.com/saphelp_nw04/helpdata/en/3b/beb13b00ae793be10000000a11402f/content.htm
and give these vales for control record
Receiver:
Port : P_SAP_IDOC
Partner number : SAP_IDOC
Partner Type : LS
Sender:
Port : SAPEI3 (same as port created in IDX1)
Partner number : EI3CLNT800
Partner Type : LS
Try this and let us know the results.
Regards,
Uma
Hi,
let me know the configurations what you have configured.
Regards
Chilla..
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hey
i followed the IDOC to File blog by prateek shah,actually i cant even send IDOC,moreover my network keeps on getting disconnected.
i jst wanna know,wat all entries i need to put in sender n receiver control structures.
On R/3 Side
RFC destination(SM59) - SAPXI
Logical System(BD54) - SAP_IDOC
Port to XI(WE21) - P_SAP_IDOC
Partner Profile(use LS created in WE20) - SAP_IDOC
On XI side
RFC Destination(SM59) - SAPR3
Port to R/3(IDX1) - XI2R3
thanx
ahmad
Message was edited by:
Ahmad
Hi,
Check in Partner profile for Idoc type under Outbound parameters.
I think these control record values are correct.
Receiver:
Port : P_SAP_IDOC
Partner number : SAP_IDOC
Partner Type : LS
Sender:
Port : SAP<Sys-ID of R/3 system>
Partner number : <Sys-ID of R/3 system>CLNT<Client number of R/3 system>
Partner Type : LS
The RFC and port created in XI system will be used for importing IDoc's metadata in XI system. Use IDX2 transaction in XI system for importing metadata.
Regards,
Uma
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
If the Idoc status is 37, then the reason is Idoc added incorrectly,
Solution:
Please checkout the Partner profile for outbound or inbound created or not. And also check the values you entered in testing IDoc, if it is existing , After creating the Partner profile we need test again by WE19.Here you can send the Existed IDoc ,or Create new test IDoc
In your case :
in We19 enter and try the following settings
Receiver:
P_SAP_IDOC
SAP_IDOC
Sender:
XI2R3
partner no --- as indicated above..
LS
Regards
Chilla..
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Ahmad,
Sender Port: P_SAP_IDOC
Sender Partner Type: LS
Sender Partner Nummer: SAP_IDOC
Rec Port: ...
Rec Partner Type: LS
Rec Partner Nummer: log System Receiver resp Adatper spec Identifier of XI Bus Syst
Regards,
Udo
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Control Record:
Receiver:
~~~~~~
Port : P_SAP_IDOC
Partner number : SAP_IDOC
Partner Type : LS
Sender:
~~~~~~
Port : SAP<Sys-ID of R/3 system>
Partner number : <Sys-ID of R/3 system>CLNT<Client number of R/3 system>
In SLD, while creating business system for R/3 specify the logical system as <Sys-ID of R/3 system>CLNT<Client number of R/3 system>. For example, if your r/3 system's ID is ABC and client is 001, then name should be ABCCLNT001
Regards,
Uma
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
101 | |
13 | |
13 | |
11 | |
11 | |
7 | |
6 | |
5 | |
4 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.