Skip to Content
author's profile photo Former Member
Former Member

Error - Internal Activation (Data Transfer Process )

Hi mates,

Please help me SOONEST POSSIBLE

I have created a Transformation from Data Source: 0CRM_SALES_CONTR_I to Data Store: 0CRM_CNT1

I have managed to sucessfully load the data into PSA

However, when I attempted to create a Data Transfer Process to send the data to the Data Store, I experienced the following error message during activation(detailed in sequence).

Activation of Objects with Type Data Transfer Process

Internal Activation (Data Transfer Process )

Post Processing/Checking the Activation for Data Transfer Process DTP_1KLUFF15DXWYKX6XNTB1

&

  • Error from PSA ****

Error when activating Data Transfer Process DTP_1KLUFF15DXWYKX6XNTB18CWZD

We are on Service Pack 9

Add a comment
10|10000 characters needed characters exceeded

Related questions

3 Answers

  • Best Answer
    author's profile photo Former Member
    Former Member
    Posted on Nov 22, 2006 at 03:26 PM

    Hi,

    The note describes similar errors as the one you are describing.

    According to the note, problems occur after installing SPS9.

    Bitte legen Sie den im Hinweis enthaltenen Report ZFIND_DTP_WITHOUT_PSA in Ihrem System an und führen Sie ihn aus. Der Report findet alle betroffenen DTPs und aktiviert sie erneut. Während der Report läuft, müssen Sie die Nummer eines Auftrags angeben, in den die geänderten DTPs aufgenommen werden. Dieser Auftrag muss muss jedoch nicht freigegeben und weitertransportiert werden, da es sich hier um einen lokalen Schiefstand handelt.

    Im SP11 wird der Report als RSBKFIND_DTP_WITHOUT_PSA ausgeliefert.

    You should first create report ZFIND_DTP_WITHOUT_PSA in your system, see note attachment and/or correction instructions. The report will find and activate all DTP's which are affected by this error. The program will ask for a change request, this is just a local request and should subsequently not be transported. In SPS11, a standard version of this program will be delivered.

    Please try the program.

    regards,

    Olav

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Nov 22, 2006 at 03:03 PM

    Hi,

    I would suggest to check and activate the datasource again first.

    Subsequently refresh and activate DTP.

    regards,

    Olav

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Nov 22, 2006 at 03:12 PM

    Hi,

    If the activation still fails, please take a look at note 994283 which could solve the issue.

    regards,

    Olav

    Add a comment
    10|10000 characters needed characters exceeded

    • Hi

      I encountered the same error previously and I've had it resolved through the help of a SAP developer. You need to apply these 2 OSS notes:

      954911 - Correction: Too many grouping fields

      954574 - Correction: Activation error PSA with DTP

      to fix the problem. Both notes are in Stack 09.

      Hope this helps.

      Regards,

      Anthony

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.