error while extracting data from r/3 to bw

[Former Member]

Hi guys,

i am trying to extract some sample data's in to bw 3.0 server from sap r/3 4.6 server, while doing this a request has been sent sucessfully from bw server but in the r/3 it throws error that incomplete control parameters in communication with bw, to rectify that i worked with transacion sbiw but i could't get proper solution, plz provide tips how to configure r/3 and bw for data extraction.

thanks in advance.

regards,

a.fahrudeen

[Former Member · Accepted solution]

Hi

Check the connection with the R3 once...

1) go to the sourcessytems

2) slect the r3 source system

3) right click and check

regards

AK

[Former Member]

Hi a.fahrudeen ,

check step by step

1. On BW Type Transaction WE20. Partner Profiles

Click on 'Partner Profile' and then 'Partner Type LS’. Click on your Source system profile to verify settings. If Source System does not exist; click on 'Partner Type LS' then Create. In your Outbound, Parameter should be ‘RSRQST’. Double click it. Outbound Options Tab Receiver Port: select RFC from above step #3. Packet Size: 1. Output Mode: 'Transfer IDocs Immediately. IDoc Type: RSRQST. Syntax Check: 'X' Post Processing Tab Type: 'US' User: Remote User (RFC_R3) Language: EN

ii. if receivers port is not available go to WE21 -> create port

R3 setting : we20

outbound :RSINFO,RSSEND

inbound :RSRQST

BW setting : we20

outbound :RSRQST

inbound : RSINFO,RSSEND

2. Entry in inbound table

i. In your Inbound Parameters should be 'RSINFO'. Double click. Inbound Options Tab Process Code: 'RSIN'. Syntax Check: 'X' Process By Function Module: 'Trigger Immediately > Post Processing Tab Type: 'US' User: Remote User (RFC_R3) Language: EN

ii. In your Inbound Parameters should be 'RSSEND'. Double click. Inbound Options Tab Process Code: 'RSDR'. Syntax Check: 'X' Process By Function Module: 'Trigger Immediately Post Processing Tab Type: 'US' User: Remote User (RFC_R3) Language: EN

3. Entry in outbound table

Entry in outbound table not found E0 400

enter : RSRQST

Click on 'Partner Profile' and then 'Partner Type LS' . Click on your Source system profile to verify settings. If Source System does not exist:

Click on 'Partner Type LS' then Create. In your Outbound Parameters should be 'RSINFO'. Double click.

Outbound Options Tab Receiver Port: select RFC from above step #3. Packet Size: 1. Output Mode: 'Transfer IDocs Immediately. IDoc Type: RSINFO. Syntax Check: 'X' Post Processing Tab Type: 'US' User: Remote User (RFC_BW) Language : EN In your Outbound Parameters should be 'RSSEND'. Double click. Outbound Options Tab Receiver Port : select RFC from above step #3. Same as RSINFO. Packet Size: 1. Output Mode: 'Transfer IDocs Immediately. IDoc Type: Basic IDoc Type (ZSBAXXX) that was checked or created in Step #5. Syntax Check: 'X

Post Processing Tab Type: 'US' User: Remote User (RFC_BW) Language: EN In your Inbound Parameter should be ‘RSRQST’. Double click. Inbound Options Tab Process Code: 'RSRQ'. Syntax Check: 'X' Process By Function Module: 'Trigger Immediately Post Processing Tab Type: 'US' User: Remote User (RFC_BW) Language: EN

Regards

sangram sutar

Message was edited by: sangram sutar

[Former Member]

Hi Sangram,

On step no 1, you mentioned "Outbound Options Tab Receiver Port: select RFC from above <b>step #3.</b>" where was your "above step #3"? Can you show me the previous steps? It's very important for me.

BTW, the same question with step #5 of yours.

Thanks,

Chuong Hoang

Message was edited by:

Chuong Hoang

[edwin_harpino]

hi Fahrudeen,

try to check connection r3-bw in R/3, SM59,

menu test->authorization.

http://help.sap.com/bp_biv335/BI_EN/BBLibrary/documentation/B84_BB_ConfigGuide_EN_DE.doc

hope this helps.