on 10-16-2006 6:06 AM
Hello gurus,
Currently sapscript is priniting fine in Laser Printer but if we issue the output in DOTMATRIX Printer the
font size changes and its printing in some other font
so , what steps do we need to take so that it prints fine
in dotmatrix printer without disturbing the current setttings.
rgds,
Aryan
Hi Aryan,
Still if you issues while printing the data on Dot matrix printer please follow following points:
1) Check the page format of your preprinted page and select the same page format.
2) the Font size which prints in the lazer print will be different in the dot matrix printer and the font goes with the dotmatrix printer format. So as said by Raghu need to set up the existing dot Matrix printer in the SAP system & this will be done by basis person and then the same basis person need to sep the character and all required details for the newly addeed dotmatri printer.
3) Tab formatalso difers forthe dot matrix printer, os need to first check on the preprinter page of thelength of the chacters and then define or maintain the same length in the layout. The lengths which are defined for Lazer will not work for the dot matrix printer.
4) Now while printing need to select the newly defined printer for the layout and then do the printing.
Do lert mek now still if you have any issues, all most in all the project i had done till date in my 8 years expriance i handeled the same type of issues and useed to solve them accordingely. So if yo have issues do let me know in deails about the issue so that i can answer them accordingely.
Regards,
Raghotham Reddy.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Thanks for your reply they will decide on the paper format based on my output what is happening here is they are comparing the forms from laser printer and expect the same alignment from Dotmatrix printer.
Currently teh Basic Settings has Tab stop 4 CH
Font Family Courier Font size 12.0
Pageformat Dina4 Portrait.
Lines/Inch 6.00
Char/Inch 10.00
Do I need to make any chages here which will fullfill my requirement ?
Hi,
Go to SPAD and check your printers installed. or change the output device type, while printing.
Feel free to revert back.
--Ragu
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
There are couple of issues here
1) The printing does not start from the place where
lazer prints from some spaces are left from
start and then it starts printing
2) the font size and the font looks different in DOTMATIX
than in lazer
3) The alignment gets disturbed
For example
17778888 XXX 19 20 In lazer
kg
17888888 XXX 19 20 In Dotmatix
kg
do I need to change the alignment ? please revert back
Outtype we will be using different output types
1) for lazer and other for dotmatrix
so no conflicts in that its only relating to
printing issue
please write back to me
your help is greatky appreciated and
yes I will give you points without fail
do not worry abt that
Message was edited by: Aryan T
Dear Aryan,
Printing with Dot Matrix Printers is hell of a job with Sap.
To my knowledge check the following steps.
1. Check in SPAD for correct printer - ofcourse u wud have done it
2. Check the printer driver compatibility assigned in SPAD
3. Not only the paper size assignment in sapscript is sufficient.. you will have to look for the paper assignment in windows of the system where the printer is connected.
4. Another very important point is that the printer driver for dot matrix printer should be installed on the windows where the printer is connected. Often its not done on XP Os. But it is recommended to do so - very imp
5. If you are not able to print vertical lines or window borders eg., SY-VLINE , then you will have to redo the sapscript.
6. Dot Matrix printers dont have the concept of windows. so rather you design your form as if it were in straight lines.
if you find this useful.Pl reward it
Regards,
Sandeep Josyula
Message was edited by: Sandeep Josyula
Hi Sandeep,
Thanks for your reply . now the vlines are not printing in the output but based on my output they will decide their paper format assuing taht the preprinted stationary will have lines ect
my only job here is to make the script run for dotmatrix
basically layout og couple of fields gets displayed here and there and the header prints half inch ahead of lazer prints .. please provide some more tips how do I control this can I check these settings here in my comp
Rgds,
Aryan
User | Count |
---|---|
95 | |
11 | |
10 | |
9 | |
9 | |
7 | |
6 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.