Skip to Content
author's profile photo Former Member
Former Member

File2Idoc Sceanrio

Hi, I am very new to XI,As per the procedure i done the all settings for File2Idoc Scenario.From sender location file was pickup by the IS.But not reach to receiver side.I check in RWB/Message Monitoring from my sender interface.The messages are intially shown "Adapter Engine - STATUS : Waiting" After some time its shown "System Error".See the below Figure of my problem.In this situation what are the things i have to check.Plz suggest.Early response is appreciable.

Add a comment
10|10000 characters needed characters exceeded

Assigned Tags

Related questions

6 Answers

  • Posted on Sep 26, 2006 at 06:17 AM

    Sent/Receive IDOC:

    you need to do the following:

    In XI

    SM59 - R3 connection pointing to R3

    IDX1 - define the port with the above dest.

    In R3

    SM59 - R3 connection pointing to XI

    WE21 - define the port with the above dest.

    WE20 - Partner profile type outbound/Inbound

    From sender location file was pickup by the IS.But not reach to receiver side.I

    >>> what do u see in message monitoring in RWB .. do post the trace here.

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 26, 2006 at 07:16 AM

    Hi Anjan,

    Just to give you a better understanding, cross check whether you have done the following steps:-

    SLD-

    1) Create a Product/Software Component

    2) Technical System pointing to R/3 system

    3) Business System for the above technical system

    In the Repository

    1) Import the Software component created in the sld

    2) Create a namespace,

    3) import the idoc and then create sender data type/message type etc and mapping

    4) Mapping Rules is depends on the requirement

    In the Directory

    1) Create a Scenario /import the business system

    2) Create Receiver/Interface determination

    3) Create communication channels for sender and receiver

    4) Sender Agreeement and Receiver Agreement.

    Then the file adapter configuration is depend on the input file format.

    Also you need to have Logical destionation created in the XI , and the IDX1 entry

    In R/3 Port, Partner profiles etc should be created

    Have a look into this document~

    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/877c0d53-0801-0010-3bb0-e38d5ecd352c

    While doing an File -> XI -> IDoc scenario, The Points to noted are:

    1. You don’t need a DT, MT or a message interface for the IDOC as it itself acts as the Message Interface.

    2. You import the IDOC and use the same in your mapping.

    3. In this configuration note that you will need a sender agreement for the file.

    4. In this configuration note that you will also need a receiver agreement for the IDOC.

    For any File -> XI -> IDoc scenario ref:

    /people/anish.abraham2/blog/2005/12/22/file-to-multiple-idocs-xslt-mapping

    Hope this helps you.

    Regards.

    Praveen

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Sep 26, 2006 at 06:15 AM

    I am unable to add the Picture here.i.e Message Display over in Message Monitoring.

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 26, 2006 at 07:04 AM

    Dear Anjan,

    Can you send the Screen print to me too.

    ID- agasthuri@gmail.com

    Regards

    Agasthuri Doss

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Sep 26, 2006 at 11:54 AM

    Hi Anjan..

    send me ur mail id ...

    i can send u docs on file to idoc and idoc configuration

    Cheers,

    raghavesh

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 26, 2006 at 04:28 PM

    Hi,

    WHat is the exact error ? Are you getting any error in the transaction code SXMB_MONI ? If so what is the error ?

    1) go to transaction SMQ2 and check the status of the Queue.

    Have a look into this blog-/people/sap.user72/blog/2005/11/29/xi-how-to-re-process-failed-xi-messages-automatically

    2) Hope all your configurations related to Idoc is correct? i.e in XI system SM59, IDX1, IDX2 entry.

    Hope this helps,

    Regards,

    Moorthy

    Add a comment
    10|10000 characters needed characters exceeded

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.