on 09-15-2006 11:59 PM
I did ALE setup to Send Idoc from R/3 to XI. I generated Idoc and sent to XI. Idoc status on R/3 is 03 - Idoc sent to R/3 System or external program ).
In XI I did setup Port for R/3 system using IDX1.
However the Idoc sent from R/3 to XI did not reached XI. What could be a problem ?. Would someone guide me please.
I did everything one possibly do using step by step guide.
When I do consistency check using BDM5, all messages are green and one in RED with folowing message
Checks in Partner System XXXXXXXXX
Test function in partner system : connection closed
Hi Ram,
As Bhavesh told, check in transaction sm58 if u can see any errors.
Did u create port SAP<SID> in idx1 in the XI box and relevant RFC destination for the same from XI Box to sending system?
Also see if these links help you...
/people/ravikumar.allampallam/blog/2005/02/23/configuration-steps-required-for-posting-idocsxi
http://help.sap.com/saphelp_nw04/helpdata/en/6a/e6194119d8f323e10000000a155106/frameset.htm
Regards,
Abhy
Message was edited by: Abhy Thomas
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Check out this link might be useful
http://help.sap.com/saphelp_nw04/helpdata/en/6a/e6194119d8f323e10000000a155106/frameset.htm
Thanks,
Prakash
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
I did setup RFC destination, Partner profiles, Ports, distribution etc on Sender R/3 System. in XI I did defined RFC destination and tested connection. Also defined port using IDX1 ( Port is SAPXXX where xxx is SID of R/3 Iam connecting to ) .
I was able to send Idoc from R/3 and Idoc status was 3 which means sent to External system.
on XI with IDX5 I was not able to see my message. We can see message usually when it hits XI box. In my case I strongly suspect Message hasn't been received by XI box.
On sender R/3 system I was not able to use SM58 transaction as I have no authorization. What else I can do without help of Basis guys to find whats happening to my Idoc which was sent to XI. Is there any fucntion I can run to see the status..
Please help..
Ram,
><i>On sender R/3 system I was not able to use SM58 transaction as I have no authorization. What else I can do without help of Basis guys to find whats happening to my Idoc which was sent to XI. Is there any fucntion I can run to see the status..</i>
This is what you need to do. When the IDOC does note reach XI and it shows succesful in We02, it implies, the IDOC is stuck in SM58 due to some TRFC error. You need to get the required Authorizations and see if there is any entry and then start debugging.
All the best,
Bhavesh
Have you created partner profile at r/3 by using transaction WE20?
Check for logical system and port, and RFC destination.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
83 | |
24 | |
12 | |
9 | |
7 | |
6 | |
5 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.