SOLMAN 7.2- SLD_UC NOT REGISTERED ISSUE

[Former Member]

Dear Freinds

We had installed the SOLMAN 7.2 successfully, and we are struck with RZ70,unable to push the data into SLD.

We had maintained host entries in both servers ( satellite system and Solman system able to communicate with each other).

Rz70 is getting failed. When we check SLD_UC RFC Connection Getting a message "Programme not registered." Please share your inputs on this

issue.

Regards

Pankaj

[mamartins · Accepted solution]

Hi, there!

That happens because of the new security features implemented on Netweaver 7.4.

You need to decrease the gateway security level (not recommended) or adjust the GW config.

Security Settings in the Gateway - SAP Library

Regards,

MM

[Former Member · Accepted solution]

Hi Manuel,

Thanks for reply, We follow the steps but still we face the same issue  RZ70 getting failed and

SLD_UC RFC getting failed.

Regards

Pankaj

[ImtiazKaredia · Accepted solution]

Make sure you are using correct gateway port. Check the access points in SAPMMC.

[mamartins · Accepted solution]

To disable the GW security, change the instance profile value gw/acl_file to 0 (zero) and restart the instance.

This is to be done on the system where is running the SLD.

[Former Member · Accepted solution]

Hi Imtiaz,

We are using SUSE-LINUX and Sybase plaform. Gateway ports are correctly Maintained

and   In rz70 we are giving

gateway host:Hostname of solman

gateway port:sapgw00

Correct me if i am wrong.

Regards

Pankaj

[ImtiazKaredia · Accepted solution]

Hi Pankaj,

Is sapgw00 the port of gateway access point. Can you paste the screen shot of the access points of SCS instance of your java stack from SAPMMC.

Thanks

Imtiaz

[Former Member · Accepted solution]

Hi Manuel,

Thanks for quick response,Once we maintain the parameter in javastack in instance profile and restart we will update you.

Can we maintain this parameter value as 0 in both abap and JAVA stack instance profiles.

Correct me if i am wrong.

Regards

Pankaj

[Former Member · Accepted solution]

Hi Manuel,

We had maintained the parameter and taken restart the SAP system.But Still No Luck.

RFC getting failed as above attached screenshot.

Regards

Pankaj

[ImtiazKaredia · Accepted solution]

Hi Pankaj,

You seem to have missed my earlier reply.

Is sapgw00 the port of gateway access point. Can you paste the screen shot of the access points of SCS instance of your java stack from SAPMMC.

Thanks

Imtiaz

[Former Member · Accepted solution]

Dear imtiaz,

Sorry i was wrong Gateway PORT is :3303, I had checked in data suppliers tab.

But i am getting below error when i do test from satellite system.

attached screenshot for reference.

gw/acl_mode=0 parameter enabled in solman both instances.

Regards

Pankaj

[manish_singh13 · Accepted solution]

Hi Sai,

If possible please attach dev_rd file from your managed system to analyze further.

Thanks,

Manish

[Former Member · Accepted solution]

Hi Manuel,

Thanks for your support finally we had able to do connection test successful from Satellite system to SLD.

Regards

Pankaj

[Former Member · Accepted solution]

Hi Imitiaz,

Thanks for your valuable inputs and support.We had rsolved the issue by placing the parameter gw/acl_mode=0 in Abap and java stack instance profile.

Now we able to send the data to sld successfully.

Regards

Pankaj

[BJarkowski]

Hi,

can you please log in to SLD, then go to Administration -> Settings, change the Section to ALL and check if you have Gateway Host and Gateway Service fields maintained?

If not, put there ABAP hostname and sapgw<instance_no>.

Then restart your instance.

Best regards

Bartosz