Auto valuation for Inspection points in Inprocess Inspection

[babarkhan_mujawar]

Hi Experts,

As per client requirement, I have mapped Inspection points for In-process inspection. Inspection characteristic are assigned to operation of routing.

whenever user record the results, auto valuation should happen based on results for each MIC's.

I have made the setting as below :-

At plant level in Customisation maintain the following

1) Plant level -  Result Recording

2) Inspection point field combination : FR1( customised as per requirement)

3)  partial Lot Assign : Partial lot for each inspection point

4) Proposal for inspection point valuation :  Maintain any of the selected set coded you have created for 03 inspection or 04 inspection( WHEN THIS IS USE, I GUES AT THE TIME OF UD??)

5) Recording configuration - No background function

Master Data Required

1) Maintain 03 inspection in MM02

2) Selected set for 03 inspection for the particalur plant

3) Sampling procedure with selection of inspection point as this mandatory

4) Sampling type - Fixed sample

5) Valuation mode - Attributive Inspection nonconf.units

6) Inspection Pts -  Free inspection pts

7) Sample size -1

😎 MIC are Qualitative

9) Control Indicators - Sampling procedure checked, Summ. recording checked, required char checked, Fixed scope checked, RR changes docs checked,

ROUTING

1) Go to CA02

2) go to header

3) Maintain inspection Point as FR1( Customised use to capture serial number)

4) Maintain partial Lot Assign as partial lot for each inspection point

5) At Operation level maintain a NO QM work center with Control key QM04.

6) double click on the control key and go to Quality Management : Inspection points

7) Maintain Inspection point  completion : AUTOMATIC VALUATION BASED ON INSP. POINT DEFINITION

😎 DONT WANT TO CREATE INSP POINTS AT TIME INTERVAL AND QUANTITY BASED.

9) Soo NO RELATION radio button selected.

10) Selection the QM operation and maintain in the MIC with above said sampling procedure

At transaction level

1) create order co01, release and save . lot will be created.

2) Do the opertion confirmation if there is any operation mentioned in the routing before the qm operation

3) go to qa32.> result > you will get a pop of all the operation with yellow traingle mentioning QM is active in that operation. double click on the QM operation

4) pop will come for entering SERIAL NUMBER AS I HAVE DEFINE INSPECTION POINTS AS SERIAL NUMBER>

When recording the results for each characteristic, its should auto valuate. but in this case it is not happening? Dont know why.

Do we required to confirm the operation use for Inspection characteristics.

Auto UD for inprocess Inspection, Is it possible??

Thanks

Babar

[rupesh_brahmankar3]

Hello,

Please read carefully SAP note 158455 - QA40, QA41, QA42: Automatic UD for production lots with defects recording, characteristic rejection: enhanced inspections

An inspection lots with origin 03, 13 or 14 are not supported for the automatic UD for production lots

special development/modification is required.

Best Regards,

R.Brahmankar

[babarkhan_mujawar]

Thanks Brahmankar for answering the doubts.

Ok, i will do that.

Can you put light on

When recording the results for each characteristic, its should auto valuate. but in this case it is not happening? Dont know why.

[babarkhan_mujawar]

Please reply waiting for solutions

[rupesh_brahmankar3]

Hello,

Refer SAP KBA    1870000 - Characteristics are not valuated automatically using transactions of result recording (e.g. QE51N, QE01..)

Automatic valuation of the characteristics is not possible and they have to be valuated manually in following cases:

No sampling procedures have been defined for a characteristic in the task list

A sampling procedure with manual valuation is defined for a characteristic in the task list

An inspection type 100% inspection is defined in the inspection setup of the material master

The target sample size is greater than the inspection lot quantity

Please check the following points,

A sampling procedure is assigned to the characteristic in the task list which has an automatic valuation rule

Flag for '100% inspection' is not set for the relevant inspection type in the inspection setup data in the material master

The sample size which is defined in the sampling procedure of the characteristic shouldn't be not greater as the inspection lot quantity

Best Regards,

R.Brahmankar

[babarkhan_mujawar]

Hi experts

While recording the results for inprocess inspection for non conforming units, we have to select the characteristic and click on valuate for valuation. And then system say Accept and reject.

During RR - don't want pop up to enter the operation quantity, Time and once all results are accepted then inspection point should be automatically valuated.

We want this to happen automatic, when we maintained the result. And its working fine for Incoming inspection.

for testing i use the same MIC which was used in incoming in In-process, still then same issue..

Please reply waiting for solutions

[babarkhan_mujawar]

Please Auto valuation for characteristic only happen to Good receipt for purchase(which involved in stock posting).

And for Inprocess Inspection, there is no stock posting.

[rupesh_brahmankar3]

Hello,

Did you set the  automatic inspection point valuation in the operation detail in the task list?

Best Regards,

R.Brahmankar

[babarkhan_mujawar]

Yes, i did but the same problem...