on 03-21-2016 12:01 PM
Dear Experts,
I am getting below error during Warehouse order confirmation.
Message No. /SCWM/HUFUNCTIONS121
Please find warehouse number control settings for my warehouse
Weight Unit LB Time Unit MIN
Volume Unit FT3 Unit of Length FT
Currency USD Factory Calend. US
Please advise what I am wrong. and when I am debug the conversion happening twice.
Step1) KG, LB
Step2) LB, FT3(failed)
Please advise.
Regards,
Vadamalai A.
I have found the resolution as below: -
In warehouse number control unit of length is maintained: 'M'. I changed it to 'FT' it is resolved. So the volume unit and unit of length should be in the same unit of measure. earlier it was in cubit foot and meter. it should be in foot and cubic foot/meter and cubic meter.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Did you find solution on the same? i am facing same issue.
error as below:
Message No. /SCWM/HUFUNCTIONS121
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Did you maintain the conversions in the product master unit of measurement view? Transaction /SAPAPO/MAT1
should have to maintain the conversion from one unit of measurement to other alternate
unit of measurements.
BR
C K REDDY
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Adding detailed log during WT creation for wave item.
"
Error during WT creation for wave item MC00 5 1
***** Product WT Creation *****
For wave 5 1
For warehouse request PDO 5272 10
For product FERT-02@ERP001; quantity 1,00000000000000 EA
***** Determine source data - start *****
Determining source data with storage type:, section:, bin:, HU:
Storage type search fully defined: No entry found
Storage type search with wild card: Search sequence PK01 and rule FIFO found
Determine stock in source storage type 0150
Determine stock in source storage bin 0150-01-01-03
Storage bin 0150-01-01-03 is not assigned to any physical inventory area
Source storage bin 0150-01-01-03 determined in storage type 0150
***** Determine destination data - start *****
Defaults for destination data: StorType:9099 Storage Sec.:0001 Stor. Bin:GI-ARE
Destination storage type 9099 checked successfully
Destination storage section 0001 is entered in storage type: 9099
Alternatives during bin search: 1st alt. Stor.Bin Type, 2nd alt. Storage Sec., 3rd alt. StorType
Access table for bin search:
Storage type: 9099 storage section: 0001 bin type: whse pos. eval.: 00000
Start of destination bin search
Stor.type: 9099, stor.area: 0001, bin type: , stock mvmt: 00000 being examined
Storage type 9099: HUs allowed but not required
Standard putaway behavior (storage type 9099)
Capacity check against storage bin GI-AREA
Weight: 41 LB are checked
against free capacity 999.999.999.999,999 KG with tolerance 0 KG
Volume: 495 FT3 are checked
against free capacity 999.999.999.999,999 LB with tolerance 0 LB
No conversion between FT3 and LB found
No warehouse task created
***** Start wave release for wave MC00 5
***** Wave release division step started for wave MC00 5
One wave read
No warehouse tasks were created for wave MC00 5
"
Hi,
I do not think that you have to maintain any conversions. But something seems to be setup wrong.
Your log shows:
Weight: 41 LB are checked --> this comes from the item.
against free capacity 999.999.999.999,999 KG with tolerance 0 KG --> this comes from the bin. In here it says that the unit is KG. And the system is ok with it. But in your first mail you wrote:
"Please find warehouse number control settings for my warehouse
Weight Unit LB"
And according to this message I would say that the first information is wrong.
Then the log continues
Volume: 495 FT3 are checked --> again, this comes from the item.
against free capacity 999.999.999.999,999 LB with tolerance 0 LB --> and now this is where your error comes from. Because it says the volume unit in the bin is LB. And of course there is no system conversion from FT3 to LB.
Your first mail says
"Please find warehouse number control settings for my warehouse
Weight Unit LB Time Unit MIN
Volume Unit FT3 Unit of Length FT"
But according the log I would say - no, it is maintained differently. Or did you maybe make changes? And the bins were created before with wrong information? Can you show a screenshot of a bin?
Brgds
Juergen
---
Want to learn EWM?
Check for EWM courses @ https://training.sap.com/curriculum/scm_ewm
Get a SAP Learning Hub Subscription: https://training.sap.com/shop/learninghub
User | Count |
---|---|
8 | |
4 | |
3 | |
2 | |
2 | |
1 | |
1 | |
1 | |
1 | |
1 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.