on 10-15-2015 3:41 PM
Hi all
I am no performing New installed Solution Manager Basic configurations and have some problems in Wily introscope installation guide(vers 9.5).
Automated Installation of the Introscope Agent via SMD
4.Launch the Introscope Setup application: SAP Solution Manager Configuration -> Managed Systems Configuration -> Step 7 Configure Automatically-> Automatic Activity “Byte Code Adapter Installation” -> “Open Java URL” (only available in edit mode). Your screen will look similar to the image below:
In my screen there is no introscope agent. The screen is attached.
What can I do? Any information will be helpful.
Best regards
Aram
Dear Aram,
As you are completing a fresh install, I am unsure of the current configuration status of your system.
But, in general please double check the following:
1. Step 2 from the sequence of steps you have referenced has been followed:
"Deploy ISAGENTJ5*.SCA which is the Introscope Java Agent 9 with SDM to Solution Manager.
You may need to deploy also ISAGENT*.SCA which is Introscope Java Agent 8."
Please also ensure to enable and disable Maintenance Mode before and after the ISAgent deployment
2. The Enterprise Manager is selected in the 'common parameters' window of 'Enter System Parameters' in MSC
NB: If your system uses Java 1.5 and up then Java Agent 9 will be used, otherwise Java Agent 8 will be used.
Best regards,
Neal
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Neal
Here are the steps that I have done.
I open Java URL where in system preparation I turn off maintenance mote for agent connection and turn on maintenance mode
and turn on maintenance mode
than in os level I open /usr/sap/<>/<>/SDM/program/RemoteGui.sh
afterwards I insert sca file that I have downloaded from SAP(ISAGENTJ515P_3-10010975.SCA ISAGENTJ506P_1-70000124.SCA ISAGENT24P_2-20006926.SCA) click next and receive this message
click ok
start deployment
confirm.
When I go to undeployment tub, I can find dhe packages that I have deployed
Than again I turn off maintenance wait for a minute for agents initialization.
I have already installed agent version 8 but nothing changed.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Aram,
Can you elaborate on which step you are currently on. If its is managed system config or Basic config. For Basic configuration, you just have to make sure that the SMD agent you installed on the Wily Host is able to get the details of your EM installation in step 3 of Basic Configuration. Once you see the EM, you can provide the users to connect the same and move to next step of Basic configuration.
The step of installing Bytecode Agent comes within Managed system configuration where you deploy on an AS JAVA system the bytecode agent depending on the NW version/JVM version as specified by Neal Genocchi.
For a freshly installed system, you must perform the system preparation, then the Basic configuration and once you have connected your managed system with this Solution Manager via SLD and in turn LMDB, then you perform Managed system Configuration for that system
Hope this helps
Regards
Aditya Khorana
Can you elaborate on which step you are currently on.
Basic configuration step 3.1 Configure CA Wily Introscope.
In this step I must connect existing Enterprise Manager to solman, But because in fresh installed solman there is no EM at first I decide install Introscope by this guide:
https://websmp202.sap-ag.de/~sapidb/012002523100019353352014E/SAPISDOC95.pdf
I have performed all installation steps but cant finish the "Introscope-Enableing SAP J2EE Systeems" step.
If I import the installation without that step I get this result
Is this normal? Must I pass this step and go ahead?
Thank you for you help
best regards
Aram
Aram,
The error you are getting because either your EM is not working or the port is not open. Is the EM installation on the same host as Solution Manager or other host.
If its on the same host go to /usr/sap/ccms/ampintroscope/bin and run ./EMCtrl.sh status and confirm the same
If the installation is on a different host than solution manager, you will have to first check EM is working or not. If yes, then see if you can telnet port 6001 from the solman to Wily Introscope host.
Regards
Aditya Khorana
User | Count |
---|---|
88 | |
23 | |
11 | |
9 | |
8 | |
5 | |
5 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.