screen not able to see in mm01/mm02/mm03

[vamshikrishna_srirangam]

Hi experts,

                I added the screen in spro i was able to see when i click on DATA SCREEN then i can able to see my subscreen but in tcode MM01/MM02/MM03 i am unable to see my screen can any one help on this.

[raymond_giuseppi · Accepted solution]

You should provide mucg more information if you want some accurate answer...

Did you read OSS note 44410 - Integrating customer-specific fields in the material master for reference / how-to guide / Check-list ?

Regards,

Raymond

[vamshikrishna_srirangam · Accepted solution]

Thank you Raymond,

                               I just did the following steps.

Step1: created append structure in MLGN table.

Step2: SPRO-->IMG-->logistics-->material master--->configure material master---->create program for customized subscreens.

step3:went to se80 then changed screen 0001 with custom fields.

step4: SPRO-->IMG-->logistics-->material master--->configure material master-->Define Structure of Data Screens for Each Screen Sequence -----> created screen sequence by copying 21 ---->went to Warehouse management DATA SCREEN -----> changed SAPLMDG1 with SAPLZM_WM_VIEW for screen 0001 and saved.

step5:  when i click on VIEW DATA SCREEN the result is

but if i open MM01/MM02/MM03 and select ware house management2 view the result is

[raymond_giuseppi · Accepted solution]

So you are enhancing EWM (I only performed this with MARA, MARC and MARD) ?

Could you check the definition / logic of your dynpro (SAP suggested to compare with SAPLMGD1 2200 as sample) Also could you compress your dynpro to use as few lines as possible to prevent no-display due to not enough space/overlapping.

Regards,

Raymond

[vamshikrishna_srirangam · Accepted solution]

Yes your right it is compression issue but i am able to see only in MM01 but not in MM02/MM03 why? and also i need to add the two new fields to the existing screen so i just copied the existing screen and then added two fields to it and when i check the PBO and PAI they are already there in my Function Group also so no issue right ? i have a doubt about it.

[raymond_giuseppi · Accepted solution]

Could you change order of subscreens (raise yours up), to check SAP behavior ?

[vamshikrishna_srirangam · Accepted solution]

Yes I did No result  if i am opening the existing screen do i need to add any logic for populating these in MM02/MM03.

[raymond_giuseppi · Accepted solution]

If you did duplicate the screen from standard, look for module "feldauswahl" (fields selection) in debug.

[vamshikrishna_srirangam · Accepted solution]

instead i debugged MM02 then i found it is calling SAPLMGD1 2732 but not calling SAPLZM_WM_VIEW 2732 i just changed in debugger then i got the result do i need to maintain anything for that please see this pics

[raymond_giuseppi · Accepted solution]

I also notice all my customer subscreen numbers were in the range 9000-9999 so no duplicates with SAP standard...

Hint: Did you look for OSS notes available in your version (with keywords T133C, OMT3B)

Regards,

Raymond

[vamshikrishna_srirangam · Accepted solution]

No some other setting is missing if i am adding my own screen also i am not able to see in MM02/MM03 any idea?

[vamshikrishna_srirangam · Accepted solution]

hi raymonds i debugged create and change in parallel then they are calling  function module T133C_READ_SUBSCREEN the difference is for MM01 screen sequence is 21 and for MM02 is 02 hahaha

[vamshikrishna_srirangam · Accepted solution]

[raymond_giuseppi · Accepted solution]

tricky