SAP PO 7.4 AS2 Sender Channel Expected URL not working

[Former Member]

Hi All,

We have SAP NW PO 7.4  and B2B Addon 1.0  installed, Now we have the configure the communication channel using AS2 Adapter. In AS2 Receiver Channel we have configured the partners URL and their details and its working fine, But in AS2 sender channel we don't have the idea about

Expected URL: ? where to create or find the AS2 URL?

We have also the followed the SAP NOTE 1828575 and configured as per the instructions.

Now we are unsure how the message will receive in the AS2 of PI

Please give us the working solutions.

Regards,

Mahendra

[Dimitri · Accepted solution]

check out these blog series:

[Former Member · Accepted solution]

Hi Dimitri Sannen,

We are also facing same issue,so we need following information from you.

how can we create expected URL in PI 7.4 single stack?

what are the steps we will do for AS2 configuration in sap pi 7.4?

We have also the followed the SAP NOTE 1828575 and configured as per the instructions, and created the URL and gave to the our partner, now we have maintain partner profile and sent a test message to partner,the message fails.

now our issue is what URL which receive in the PI side and where will be this message can be seen.we are unsure how this works.

please advice us further.

regards,

Vijayakumar

[Dimitri · Accepted solution]

Hi,

The blog series I refer to is based on a SAP PO 7.4. All required information should be there.

Also, look at for more information about the URL.

Kind regards,

Dimitri

[Former Member · Accepted solution]

Hi,

where should we find the partner name and AS2 name in PO 7.4?

please give us sample URL for SAP PO 7.4 .

regards,

Vijayakumar

[Dimitri · Accepted solution]

Have a look at Configuring the Communication Channels with the AS2 Adapter - SAP NetWeaver Process Integration, bus...

[Former Member · Accepted solution]

Hi Dimitri,

Thanks for your reply

We have configured the AS2 adapter with the SAP Note and provided the URL to the partner.

Eg: http:\\publicip:port\nwa\as2

Now we posted a test message using Partner URL and posted the message. But we encountered issue.

We are unsure how to configure the AS2 adapter (our scenario is to post the message and receive the message)

We have created the above said URL and provided to our partner.

We have configured the partner URL in our AS2 adapter (in the Recipient URL path we have given entire URL of the partner) we are not sure if this is correct ?

So what is the correct configuration we need to maintain in receiver channel column (Recipient URL)

Please advise.

Regards,

Mahendra Madhan

[Dimitri · Accepted solution]

Hi,

The recipient URL should be provided by your receiving partner. Did you contact them? Did you test?

What does the receiver see in their system?

Kind regards,

Dimitri

[Former Member · Accepted solution]

Hi Dimitri,

Yes I have got their recipient URL, configured in my receiver communication channel AS2 and got the below communication channel monitoring as "channel will deliver to http://as2dev.com:port/as2"

Now my doubt is in Sender channel what will be the Expected URL and what URL should provide to the partner?

Please advise.

Regards,

Mahendra

[Former Member · Accepted solution]

Hi Dimitri,

Thanks for your reply.

we have sent test message to the partner but my partner received the message as error, please refer below text.

"500 is an internal server error."

Meaning there is a mismatch with our setup.

also they should maintain MDN request type to Async?

please suggest us.

Regards

Mahendra

[Former Member · Accepted solution]

Hi Mahendra,

The PI default AS2 URL -  http://Host:port/AS2 .

The above mentioned AS2 URL of PI must be give to partner. they will send a test message use this url ,identifier id and public certificate.

Regards,

Vijayakumar

[Former Member · Accepted solution]

Hi Vijay,

Thanks..

I have now configured the AS2 channel and now the Outbound is working fine.

Regards,

Mahendra

[Former Member]

Hi Mahendra,

Please have a look at

Configuring AS2 Sender Channel for Inbound Message Processing - SAP NetWeaver Process Integration, b...

Regards,

Vijayakumar

[Former Member]

Hi Mahendra

The expected URL, is working with logical partner, the partner creates the url which you have provided in his Non SAP PI AS2 server , and sends the message, these message received in your PI server.

You have to provide some valid path in your PI side and back to system.

Please share  the business scenario details we could help you further.

Thanks & regards,

Ambi