Skip to Content
avatar image
Former Member

Inconsistency in Availability check at Delivery level

Hi,

I have a material code in which available stock as per CO09/MD04 is 24 qty.

I have created a sales order in my production client with a qty of 20 for this material. Since 24 is available in stock as per CO09, the qty in sales order got confirmed. Now when I am creating delivery for this order, in delivery system is confirming only 4 qty. When I try to manually change the qty to 20 in dleivery, system is giving in error log, "Only 4 qty of material available". When I try to check availability from delivery document through Environment - Availability it is giving me a different value as compared to CO09.

This is happening with almost all my materials in which stock is very less. System is allowing delivery only for the (available qty - SO qty).

However when I go through VL01N t.code and enter the respective line item number and press enter, system is confirming the entire 20qty and allowing to create delivery and do PGI.

My configuration for OVZ9 is as follows:

1. No Safety stock is selected

2. Not checking RLT

3. Considering Sales requirements, Delivery reqmts and reservations (I have done the same settings for order - A and delivery - B in OVZ9)

4. I have activated the soft block in OVZ2

I have also tried executing the report SDRQCR21, but there was no effect.

Request you to kindly let me know where I must have gone wrong.

I have checked a lot of posts related to this on sdn, but there was not even a single post that could give me a solution to my problem.

Thanks & Regards,

Rohan Gudavalli

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

3 Answers

  • Best Answer
    avatar image
    Former Member
    Jan 26, 2015 at 09:59 PM

    Rohan,

    Now when I am creating delivery for this order, in delivery system is confirming only 4 qty.

    However when I go through VL01N t.code and enter the respective line item number and press enter, system is confirming the entire 20qty

    Seems to be a conflict here.  If you are not using VL01N in the first attempt, what are you using?

    ATP for the delivery is usually performed automatically during creation.  In the most common configuration settings, the delivery cannot be created unless there is adequate availability.  You don't even get to the delivery creation screen.

    Best Regards,

    DB49

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member Former Member

      Hi all,

      This issue has been raised with SAP and SAP has suggested to implement the note 1909466 to resolve the issue. Following has been quoted by SAP:


      please implement the attached SAP Note 1909466. This note has solved similar issues in the past.
      After implementing the note please test the system behavior again. In case you experience the same issue, please send the incident back to us"


      Note has been implemented and issue has been resolved. Hope this helps somebody with the same issue in future.

      Closing the thread.

      Thanks & Regards,

      Rohan Gudavalli

  • Jan 27, 2015 at 05:32 AM

    1. Check the Checking Group for Availability Check in material master

    2.Check the stock at batch level

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member

      Hi,

      Checking group in material master is correct and the stock at batch level is available as stated in my original post.

      Thanks & Regards,

      Rohan Gudavalli

  • Jan 27, 2015 at 11:04 AM

    Could be related to a different storage location being determined during delivery creation.

    Or if you are executing batch determination during delivery creation, it could happen that a batch gets determined but there is only 4 available in that batch.

    So check to ensure that there is enough stock in storage location and batch (if batch managed).

    A screenshot of your CO09 would be useful for us to analyse.

    Add comment
    10|10000 characters needed characters exceeded