Skip to Content

purpose of LOGGING_SYNC

Hi

can any one pls explain why we open the log for SYNC scenarion from 0 to 1.(Category > Runtime, Parameter> LOGGING_SYNC current value to 1)

and i appreciate if you could explain even reast of the catagories aswell.

PF attached FYI.

Thanks in advance

Capture.JPG (68.9 kB)
Add a comment
10|10000 characters needed characters exceeded

Related questions

3 Answers

  • Best Answer
    author's profile photo Former Member
    Former Member
    Posted on Dec 29, 2014 at 11:34 AM

    Hi Annapureddy Kasi viswanath,

    I thinks this information clear your point of veiw:

    Synchronous messages (Best Effort) will only be persisted if an error occurs during processing or if the parameter LOGGING_SYNC (ABAP only) is set. Setting LOGGING_SYNC is not recommended to reduce processing overhead.

    Use the configuration parameter LOGGING or LOGGING_SYNC (category RUNTIME to activateLOGGING of asynchronous or synchronous messages locally for the whole Integration Engine. This means that all service calls of all pipelines of this Integration Engine are logged.

    If you increase this level, you will get minute details. 0 is default level.

    Add a comment
    10|10000 characters needed characters exceeded

    • Hi Annapureddy Kasi viswanath

      What is the t-code for configure the logging, in the ECC i had configured with SXMB_ADM and ECC connected with SAP-PO and the t-code message used SXMB_MONI

      but in S/4HANA uses SRT_MONI or SRT_ELOG and the administration t-code is SRT_ADMIN to configure the services and SBGRFCCONF configure inbound message, but i haven't found where configure the level logging, loggind_sync, tracer, etc.

      Could you teach the t-codes or the secuence to activate for S/4HANA.

      tnx

  • Posted on Dec 29, 2014 at 09:48 AM

    Hi,

    Please check following for details:

    Integration Engine - What's New in SAP NetWeaver 7.3 (Release Notes) - SAP Library

    Integration Engine and Queue Configuration on ABAP systems for AEX scenarios

    With the parameter LOGGING_SYNC the logging of synchronous messages for all pipelines of an Integration Engine can be activated (which improves error analysis and tracing)

    0 – deactivated

    1 – activated

    Regards,

    Azhar

    Add a comment
    10|10000 characters needed characters exceeded

    • Azhar Shaikh Annapureddy Kasi viswanath

      If your Msg is Sync message, by default it will not be logged (deactivated) in sxmb_moni...inorder to enable logging of sync msg you need to Activate this parameter in sxmb_adm

      In some cases if the data is highly confidential one (in Prod), you can use this feature to disable logging. But in Dev/ QA we generally Activate it inorder to have better trace/tracking/debugging of the sync messages

      hope it helps

      Regards,
      Azhar

  • Posted on Dec 29, 2014 at 09:45 AM

    Hi,

    Logging_Sync is required to log sync messages. If you have synchronous interface and if you want to see the request and response in monitoring (MONI) then you need to change the value of parameter to 1.

    refer the below blog

    XI: I cannot see some of my messages in the SXMB_MONI

    regards.

    Harish

    Add a comment
    10|10000 characters needed characters exceeded

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.