SBO Mailer Test Connection Error

[former_member209066]

Dear All,

SBO Mailer Test connection following error showing for SAP B1 9.0 PL 9. Please give the solution.

Thanks,

Nithi

[former_member209066]

Hi All,

Please any one give me the suggestion.How to rectify this problem?

Thanks,

Nithi

SBO Mailer Test Connection Error

[former_member209066]

Hi ,

This Configuration working perfectly. But its not taking Users mail Id.This configuration taking only for Configuration mail id.

Please any one give me the suggestion.How to rectify this problem?

Thanks,

Nithi

[Former Member]

Hi The SMTP has to be enabled on the server in active directory

Understanding Transport Permissions Architecture: Exchange 2010 Help

Troubleshooting Permissions

During the protocol conversation, the SMTP server may reject certain commands because there is a lack of permissions. Table 9 lists the most common protocol rejection messages and the permissions configuration that causes the error.

Table 9   Common protocol rejection messages and their causes

SMTP server response	Cause
530 5.7.1 Client was not authenticated	The sender specified in the MAIL FROM field of the SMTP protocol doesn't have permission to submit to this server. The ms-Exch-SMTP-Submit permission must be granted to the sender.
535 5.7.3 Authentication unsuccessful	During the AUTH phase of the SMTP protocol conversation, the provided credentials were incorrect or the authenticated user doesn't have permission to submit to this server.
550 5.7.1 Client does not have permission to submit to this server	The sender specified in the MAIL FROM field of the SMTP protocol conversation was authenticated but doesn't have permission to submit to this server.
550 5.7.1 Client does not have permission to send as this sender	The sender specified in the MAIL FROM field of the SMTP protocol conversation is an address in an authoritative domain. However, the session doesn't have the ms-Exch-SMTP-Accept-Authoritative-Domain-Sender permission. This might occur if a message was submitted from the Internet to an Edge Transport server from a sender address for which the Exchange organization is authoritative.
550 5.7.1 Client does not have permission to send on behalf of the from address	The authenticated user doesn't have permission to submit a message on behalf of the sender that is specified in the header of the message. Also, the session doesn't have the ms-Exch-SMTP-Accept-Any-Sender permission.
550 5.7.1. Unable to relay	The recipient domain to which the message is addressed isn't within any of the accepted domains defined for this organization. Also, the session doesn't have the ms-Exch-SMTP-Accept-Any-Recipient permission.

Cheers

[former_member209066]

Hi,

Thanks for reply.Its not working.Any one please give me the Solution.

Thanks,

Nithi

[Former Member]

Hi Nithi

In the SMTP Relay made exception to your B1 Mail Server IP and marked your email account as SMTP Authentication not Required and any one can send email on behalf of this account?

I think, If you can replay with what solutions you have tried based on the help/suggestions you received from other mates then it would help all to give you better support

Cheers

Sandy

[former_member209066]

Hi Sandy,

I am not understanding.Email is working Perfectly,but not taking users mail id.

Thanks,

nithi

[kothandaraman_nagarajan]

Hi,

Did you define email id for that particular user under Setup--->User?

Thanks & Regards,

Nagarajan

[former_member209066]

Hi Nagarajan,

Thanks for reply. I already configure user Setup.

Thanks,

Nithi

[former_member209066]

Hi,

Please any one give me the Solution.

Thanks,

Nithi

SBO Mailer Test Connection Error

[former_member229757]

Hi

   Try these changes....

Regards

Vinoth

[former_member209066]

Hi,

Thanks for reply.Its Not Working.

Thanks,

Nithi

[former_member209066]

Hi,

Please give me the Solution.

Thanks,

Nithi

[kothandaraman_nagarajan]

Hi,

Did you check attached threads in my last reply?

Thanks & Regards,

Nagarajan

[former_member209066]

Hi Nagarajan,

Yes but not working. Only for See4c Configuration Not Working.

Microsoft.Net

Basic Authentication

Working good.But its not taking user maild id.Its taking only for Configuration mail id.

Please give me the solution.

Thanks,

Nithi

[Former Member]

Hi Nithi,

Please check below links.

Hope this helps

--

--

Regards::::

Atul Chakraborty

[Former Member]

Hi Nithi,

If there is a issue for sending mail after the configuration is complete i suggest you to Please check the SMTP Port you have entered, check it with 995 or 993 instead of 25.

Hope this help.

Thanks,

Regards,

Sudhir

Message was edited by: Sudhir Sharma

[former_member209066]

Hi,

But this Configuration working for perfect.

But this type of configuration taking the only configuration mail id.Not taking the Users Mail id.

Thanks,

Nithi

[agustin_marcoscividanes]

Hi

SBO Mailer only needs one user / one password valid for the mail server.

SBO Mailer takes the email address from the SBO current user as sender.

Kind regards

Agustín Marcos Cividanes

[former_member209066]

Hi,

Yes Correct but email address not getting from SAP current user for Microsoft.Net Configuration .

Thanks,

Nithi

[kothandaraman_nagarajan]

Hi,

Check test connection without login authentication and let me know result.

Thanks & Regards,

Nagarajan

[former_member209066]

Hi

Thanks for reply. Without login authentication Test connection is success. But mail sending failed.

Thanks,

Nithi

[kothandaraman_nagarajan]

Hi,

Please post if any error message to check.

Thanks & Regards,

Nagarajan

[former_member209066]

Hi,

Following error message

Thanks,

Nithi

[agustin_marcoscividanes]

Hi

in Windows Event Viewer you will find an error message.

Can you send the number error and the text?

Kind regards.

Agustín Marcos Cividanes

[former_member209066]

Hi,

Please Check this picture

Thanks,

Nithi

[kothandaraman_nagarajan]

Hi,

Please refer below threads:

http://scn.sap.com/message/15086103#15086103

http://scn.sap.com/thread/3330568

Thanks & Regards,

Nagarajan