Error While Transporting

[Former Member]

After transporting the BI request to production system,we are getting the following error.

We activated in development system and transported.However we are getting the error.

InfoObject 0MATERIAL is not available in active version

InfoObject 0MATL_GROUP is not available in active version

InfoObject 0MATL_GRP_1 is not available in active version

InfoObject 0MATL_GRP_2 is not available in active version

InfoObject 0MATL_GRP_3 is not available in active version

InfoObject 0MATL_GRP_4 is not available in active version

InfoObject 0MATL_GRP_5 is not available in active version

Note : All Infoobjects are getting the above error.

Please guide us

Regards,

Kavitha

[Former Member]

Hi,

Please check whether they were transported to your Quality server properly or not, if there it was success then please check what is the path they were transported, means: Dev -> Q -> Prod or Dev -> Q and Dev -> Prod. If you are having the later case then please try to reactivate and adjust by 'RSDG_IOBJ_REORG' program in se38 and try re-transporting. Please try to adjust in se14 tcode.

Just in case this might be a situation like: check your info object catalog for any other info objects, why is this because at times it happens like some unnecessary info objects are also being carried out by the catalog which causes the failure of the whole package.

[abdullahqureshi]

Hi,

In a single TR collect only info objects purely for those you are getting error also once again check in target system with their Data targets for all needed info objects. Beacuse may be possible next time you will get the error for different info objects so make sure all the info objects those are used in your ETL should be present there.

Collect info objects from transport connection by selecting Data targets -> grouping (only necessary objects) & Display (List).

After the successful transport of all the info object. Re import your error TR and I think it is mix up of different type objects.

[former_member199945]

To move BI iob;s need to follow Sequence , i think u didn't follow Sequence.

Refer Below Doc for sequence

Have u followed same sequence?

[Former Member]

Hi,

Yes we have done as in the document.

Kavitha

[former_member199945]

Check those IOBj's in DEV system either active or not like omaterial & 0mat_grp1 all iobj's which are showing in screen shot.

If all those iobj's are avialble in active version in DEV then try to recollect again with new request & move that TR.

[former_member182998]

Hello Kavitha,

It seems the Objects are not properly activated in the system . Try to activate the same with RSD1 T code  and retransport them to the destination environment .

You can cross the Info Objects in table RSDIOBJ, if all the versions of IO ( D, M,) are available .

Hope this helps !

Regards

Yogesh Narwani

[Former Member]

Hi all,

Thanks for all the replies.

The suggestion you gave above was tried by me already.Eventhough i am not getting the IO transported to the production system.

In production system STMS is not installed.Please confirm whether this would be a cause for these errors?

Please suggest me other ideas to get the IO successfully transported.

Regards,

Kavi

[former_member199945]

Either u are facing only for this iobj's or for other iobj's also check once?

STMS is just used  for checking Transport route.

U can check in Dev using STMS tcode either DEV to PRD route configured or not.

[RamanKorrapati]

Hi,

At what step your facing this error.

While releasing at dev or while importing at prod?

Actually what objects you collected into trandport request?

In production system STMS is not installed.Please confirm whether this would be a cause for these errors?

No that's not the cause.

Error clearly said as object was in active.

Can you share your errog logs screen shot.

Thanks

[Former Member]

Hi,

Can you just activate  "0MATERIAL" and try to import that only.

Share with us screenshot of the issue if it happens.

Best Regards,

Arpit

[Former Member]

[RamanKorrapati]

Hi,

Above error screen referring CPMB - Mean its related to BPC objects.

Seems like you have BPC on your BW server.

is there any relevant about error screen shot and mentioned info objects(0MATERIAL)?

please tell me which objects you have collected into transport?

Even how you collected info objects?

Have you transported respective applciation component, info area,info obejcts catalog?

Thanks

[Former Member]

[KodandaPani_KV]

Hi,

Activate the 0MATERIAL info object

you can activate the object through program RSDG_IOBJ_ACTIVATE

once activation done collect the one more TR and move to target system.

as you said STMS not yet installed check with the basis team they will help.

after collecting the objects check the SE09.

select your TR -> go request tab-> select the complete check -> task/request.

Thanks,

Phani.

[KodandaPani_KV]

Hi,

your are not yet activated the info objects suggested by raman.

activate the info objects using the RSDG_IOBJ_ACTIVATE

then collect the one more TR then do transport.

Thanks,

Phani.

[former_member199945]

1. Need to recollect active version of that Iobj's  checc once again in DEV either those iobj's active or not if those iob'j's are active then again recollect & send.

or

2. u can activate through program directly.

RSDG_IOBJ_ACTIVATE

[RamanKorrapati]

Hi,

Error clearly saying as mentioned objects are inactive.

0MATERIAL

0MATL_GROUP

0MATL_GRP_1

0MATL_GRP_2

0MATL_GRP_3

0MATL_GRP_4

0MATL_GRP_5

Check at T code - RSD1, whether info object was active or not.

at dev system each info object activate them again and collect into new transport and move across the landscape.

P.S - always collect objects into transport at RSA1--> transport connection, if have any issues, here its self we will know it.

Thanks