on 02-26-2014 2:27 PM
HI,all
Learn from the link of
I can not find the registered Program ID as the picture 1.4.
and when i go to tcode:RZ70 ,input the gateway host <PO7.4 HOST> and the right gateway service .but when i execute, it failed ,the message showed as following
: Execute program: _SLD_APPL_SERV
: Execute program: _SLD_BCSYS
: Execute program: _SLD_CLIENT
: Execute program: _SLD_COMPSYS
: Execute program: _SLD_DBCON
: Execute program: _SLD_DBSYS
: Execute program: _SLD_GWSRV
: Execute program: _SLD_HTTPSERV
: Execute program: _SLD_INSTPRD
: Execute program: _SLD_INSTSC
: Execute program: _SLD_INSTSP
: Execute program: _SLD_IPSERV
: Execute program: _SLD_LIVECACHE
: Execute program: _SLD_MSGSRV
: Execute program: _SLD_NWSYS
: Execute program: _SLD_RCC
: Collection of SLD data finished
: Data collected successfully
: RFC data prepared
: Used RFC destination: SLD_UC
: RFC call failed: Error when opening an RFC connection (CPIC-CALL: 'ThSAPOCMINIT' : cmRc=19 thRc=7
what should i configure to avoid this problem? thx.
Hello,
Dis u test SLD_UC destination ?
Thanks
Amit Srivastava
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
SLD_UC connection test failed too and have the same message:
Logon Connection Error
Error Details Error when opening an RFC connection (CPIC-CALL: 'ThSAPOCMINIT' : cmRc=19 thRc=7
Error Details ERROR: Error (Msg EGW 748 not found)
Error Details LOCATION: SAP-Server SJERPQS_SEQ_10 on host SJERPQS (wp 9)
Error Details COMPONENT: CPIC
Error Details COUNTER: 9
Error Details MODULE:
Error Details LINE:
Error Details RETURN CODE: 748
Error Details SUBRC: 0
Error Details RELEASE: 721
Error Details TIME: Wed Feb 26 23:04:08 2014
Error Details VERSION:
Hi Steve - Please check the SAP note 1476839 - PI SLD: Error accessing a remote SLD via RFC
by the solution
"Logon to the remote SLD with "http://<host>:<port>/sld" and
navigate to 'Administration --> Details --> Data Suppliers' and check
whether the 'RFC server threads' are running. They are very likely not started
correctly. Pay attention to the 'Gateway Host' and 'Gateway Port' entries
displayed there. Verify whether they are correct.
You can change 'Gateway
Host' and 'Gateway Port' settings with 'Administration --> Settings -->
Section datasupplier'. Leave the fields empty to use the defaults. Restart the
SLD after that.",
I found that my datasuppliers message shows like this
"[UP] Local processing, queue size: 0
Updated SLDs:
(local)
sld/active
Last data received: J2EESystem at Wed Feb 26 21:05:40 CST
2014
RFC server threads:
[UP]
NUC:XX.XXX.XXX.XX_sapgw01_SLD_NUC_288131791
[UP]
UC:XX.XXX.XXX.XX_sapgw01_SLD_UC_1250850160
[UP]
NUC:XX.XXX.XXX.XX_sapgw01_SLD_NUC_739872972
[UP]
UC:XX.XXX.XXX.XX_sapgw01_SLD_UC_319202832
Gateway Host:
XX.XXX.XXX.XX
Gateway Port: sapgw01"
IF it means the RFC server threads running?
If the host is your ABAP(ECC) system then yes..
Also have a look at the below therad if it helps..
Hi Li,
Can try the following options
1.Try to give the ip address of PO host and gateway service
2. Look into your gateway security files secinfo and reginfo in your ECC system
https://help.sap.com/saphelp_nw73/helpdata/en/e2/16d0427a2440fc8bfc25e786b8e11c/content.htm
Regards,
Akram
i have set the gateway host by ip and
my gateway security secinfo is
P TP=* USER=* USER-HOST=local HOST=local
P TP=* USER=* USER-HOST=internal HOST=internal
my security reginfo is
P TP=* HOST=local CANCEL=local ACCESS=local
P TP=* HOST=internal CANCEL=internal ACCESS=internal
P TP=SLD_NUC HOST=local CANCEL=local ACCESS=local
P TP=SLD_NUC HOST=internal CANCEL=internal ACCESS=internal
P TP=SLD_UC HOST=local CANCEL=local ACCESS=local
P TP=SLD_UC HOST=internal CANCEL=internal ACCESS=internal
P TP=SAPSLDAPI_PID HOST=local CANCEL=local ACCESS=local
P TP=SAPSLDAPI_PID HOST=internal CANCEL=internal ACCESS=internal
i have reload in smgw.
i also have configure the gateway host and gateway service in SLD-ADMINISTRATOR-DETAILS-DATA SUPPLIERS
the detail are:
[UP] Local processing, queue size: 0
Updated SLDs:
(local)
sld/active
Last data received: J2EESystem at Thu Feb 27 11:09:36 CST
2014
RFC server threads:
[UP]
NUC:[PO HOST_IP]_sapgw01_SLD_NUC_1676757962
[UP]
UC:[PO HOST_IP]_sapgw01_SLD_UC_311176846
[UP]
NUC:[PO HOST_IP]_sapgw01_SLD_NUC_163957397
[UP]
UC:[PO HOST_IP]_sapgw01_SLD_UC_1607303763
Gateway Host:
[PO HOST]
Gateway Port: sapgw01
I still have no idea why this RZ70 Wrong.
the wrong message is
: SJERPQS_SEQ_10 : Collection of SLD data finished
: SJERPQS_SEQ_10 : Data collected successfully
: SJERPQS_SEQ_10 : RFC data prepared
: SJERPQS_SEQ_10 : Used RFC destination: SLD_UC
: SJERPQS_SEQ_10 : RFC call failed: Error when opening an RFC connection (CPIC-CALL: 'ThSAPOCMINIT' : cmRc=19 thRc=7
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
87 | |
23 | |
11 | |
9 | |
8 | |
5 | |
5 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.