Skip to Content
avatar image
Former Member

DG Filling

Hello

I have a query on DGM.

I need to create DG Master for a Product which contains two dangerous goods.

Consider a marketable product (X) and it contains two dangerous goods ( A1) & (A2) of class 6.1 and 8.respectively.

  • (X)
    • (A1)
    • (A2)

To fulfill this requirement i created a Material X and a Specification X (Spec Type Real_Sub). for the Marketable product.


Further i created UN Listed Substance for A1, DG Classification for A1 (IATA & IMDG) and Real_Substance for A1. And assigned the material X.


Similarly I created UN Listed Substance for A2, DG Classification for A2 (ADR & CFR_RAIL_C) and Real_Substance for A2. And assigned the material X.


On performing the DG filling i get the following message.

Filling completed; problems have occurred (see log)

The message guides to Message no. DGA404. On a check this message is not maintained in (hide messages in import log).


Any responses on this particular scenario would be highly appreciated.


Thanks

Add comment
10|10000 characters needed characters exceeded

  • Follow
  • Get RSS Feed

5 Answers

  • Best Answer
    Jan 17, 2014 at 02:53 PM

    Hi

    Please check log. in Transaction DGP7.

    If the log does not contain any entries, this could be due to the settings in the IMG activity Environment Health and Safety -> DangerousGoods Management -> Interfaces: Filling and Distribution -> Common Settings -> Hide Messages in Import Logs. ( Message Class would be DGA and Msg.404)

    Recommendation:

    To determine the cause of the error, deactivate the hiding of the messages in the above IMG activity.

    Check the result of filling.

    Thanks

    Add comment
    10|10000 characters needed characters exceeded

    • Hi

      explanations of Balajee a very helpful. But I would like to add some info:

      You have material X assigned to specification X, and you have material Y assigned to specification Y.

      Both will get data in property tree. Based on the data both will get a dangerous goods master. Now you perform a "physical" mix. Therefore you need a new material Z and a new specification Z. Then once again data is maintained and DG classification need to be done and therefore Z will get its own dangerous goods master data.

      But it seems to be that during filling of dangerous goods master of material Z an error message come up. Here I believe the approach/hint of Sunil might help.

      But from business point of view (maintenance etc.) it seems to be that you have prepared set up correct.

      PS: please read cross the DG filling part of SAP online help; there are a number of subprocesses involved which I did not mentioned here assuming that you are not using these in your scenario; but this assumption might be wrong; I am sorry. In contrast to SDS distribution no OSS consulting note is available explaining the DG part of SAP EHS.

      C.B.

  • Jan 17, 2014 at 12:45 PM

    Dear Meghana

    Here due to presence of A1 &A2 Product X will become a Dangerous goods , so you have to create the specification for Product X (Real Sub) and give the reference of DG Class and assign the respective material to real substance and fill the DG , here you have to mention A1 & A2 are hazard inducing susbtances at Hazard Inducers field with respective Trasport regulation in DG Classification.

    Here A1 & A2 will also a materials , so you have to assign the A1 & A2 materials to real substances of A1 & A2 and assign the respective DG class reference and then run the fill activity.

    Balajee

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jan 20, 2014 at 01:16 PM

    thanks a lot for your valuable responses i was able to run the DG Filling process.

    On assigning of the individual components A1 & A2 as Hazard Inducers in the Dangerous Goods Classification i was able to complete the Filling activity.

    Thanks once again to all the members for your responses.

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jan 20, 2014 at 01:17 PM

    thanks a lot for your valuable responses i was able to run the DG Filling process.

    On assigning of the individual components A1 & A2 as Hazard Inducers in the Dangerous Goods Classification i was able to complete the Filling activity.

    Thanks once again to all the members for your responses.

    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Jan 20, 2014 at 01:17 PM

    thanks a lot for your valuable responses i was able to run the DG Filling process.

    On assigning of the individual components A1 & A2 as Hazard Inducers in the Dangerous Goods Classification i was able to complete the Filling activity.

    Thanks once again to all the members for your responses.

    Add comment
    10|10000 characters needed characters exceeded