on 11-13-2013 12:50 PM
Dear All,
I trying to get data from 0FI_GL_10 to PSA.
When I run INIT first it got an error Caller 09.
I deleted INIT infopackage and create a new one.
Now when I run new INIT info package it says "Delta Already Loaded for request".
I tried to follow http://scn.sap.com/message/11126522
Suman's steps but not getting any request under schedule menu.
I also tried to follow http://scn.sap.com/thread/1897878
Pavan's steps but not getting result.
Please suggest suitable steps.
Hi Harshil,
I think you facing this problem.
Error message from the source system
Diagnosis
An error occurred in the source system.
System Response
Caller 09 contains an error message.
I was also facing the same problem yesterday. and i resolved this today morning.
Try this step.
Steps.
1. Activated data source in DEV and transported in PRD.
2. Replicated and activated data source in PRD.
3. Did full load.
4. Then init without data.
5. Delta.
I hope this will work for you....
http://scn.sap.com/message/14527670#14527670
Regards,
SM
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Dear Harshil,
As per my understanding, when you loading the init infopackage, it shows 09 error.
Please use below points:
1) First delete the previous INIT info package.
2) Check there is any PSA request, if any plz delete.
3) For example: consider 2lis_02_itm datasource.
4) Create one new INIT Infopackage. Here we have two options init with data transfer and init without data transfer. For this select ( Init without data transfer ).
5)While creating Info package, under scheduler delete flag ( Initialization for the source system )
5) Once delete Save infopackage and schedule the data load.
6) Once complete the loading, it contains only one data.
7) So, again you should do the repair full request to pull the rest of the data.
Check these option. If not work, show screen shot...
Regards,
Baskaran
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Harshil,
the above steps will simply delete the OLD init selections and next performing INIT without data transfer means simply we are setting delta pointer.
If you execute FULL or delta you will get the caller 09 error as there is issue at Source side with the data soruce.
Try to execute RSA3 in ECC and check if you are able to extract and see the data?
Regards
KP
Hi,
Once you replicate your data source it might be in 3.x. you need to migrate to 7.x by using RSDS (from your 2nd step pic, migrate 3.x data source----> data source) or
at RSA1--> data source 0FI_GL_10--> right click --> migrate --> with export. later you can activate by using above program.
Thanks
Hi,
Source system connections are in place?
check your source system name and data source name. is it 0(zero) or O.
Go to RSA1 --> data source, find 0FI_GL_10. double click on it.
see it active or not. if not click on active icon.
Try again and again. All steps are there; take and time check one by one again do it.
Thanks
Hi,
if your init was success then your data source 0FI_GL_10 will be available at ecc system RSA7.
Assuming as you checked at your info pack--> menu scheduler --> init options for source system. there will be an entry for init. if you won't see there then you can do init again.
Thanks
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Then from your info pack monitor(full load) menu Environment--> job overview--> job in the source system,prompt for ecc user id and pass word, enter,m you will get info pack backend job at ecc. select your job and click on job log details. you will see about your error details in full details.
Please log details.
Thanks
Be clear please.
Your init was success, are you doing init again. are you at prod or dev.
If you plan to do again init then delete the existing and do as you need.
See its depend on how you want load.
Ex: if you want load data with init then go for init with data transfer. so full load no need to load.
init with data = Full load + enabling delta options.
If you want enable delta only then go for init with out data transfer and you need to run full load.
Hi Harshil,
Sorry, Those are not required details. no idea how you checked.
Go to your failed info package--> monitor, Header tab, copy Request id.
Go to ECC system SM37, Job name: BI<Request id copied at bw>
User name: *
Date ranges: 12:11:2013 to 15:11:2013
status: Cancel, active and success.
You will get your job, select job and click on Job log details icon from tool bar.
Thanks
please check it carefully,.
You may be doing something wrong selections at SM37.
you shared one job details at 10:46AM today, go to the same job and select your job, click on job log details.
Or
Go to your failed info package monitor menu Environment --> job overview --> job in the source system, enter ecc user id and password.
you will get your job, select job and click on job log details.share those details.
Thanks
ECC job log what it saying? if your info pack still yellow then at ecc job log may have some information. have you checked?
Wait 20 to 30mts, if you don't see any information at ecc job log, cancel your ecc job and cancel info pack, go to info pack, monitor screen, status tab, change technical status as red.)
Take abap help and debug your data source at info pack level.
if not resolved then take sap global help.
Thanks
User | Count |
---|---|
93 | |
10 | |
10 | |
9 | |
9 | |
7 | |
6 | |
5 | |
5 | |
4 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.