cancel
Showing results for 
Search instead for 
Did you mean: 

Problem with Wily Installation SM 7.1

Former Member
0 Kudos

Dear All,

We are facing some problems during the installation/configuration of Wily 8.0 in our system landscape.

The following tasks are done and seem to be OK:

- Installation of Wily Enterprise Manager 8.0 on our Solution Manager System

- Installation of Diagnostics Agent 7.3 on our Portal and BO Servers

- Agents are connected to the Solman

- Portal and BO System are configured in solman_setup including DA and Wily configuration

So far so good but in the Wily Introscope Guide there is a point where the agent is configurated (Chapter 4). We deployed the ISAGENTSMD* with SMD but the next point is "Lauch the Introscope Setup application". But where can I find this?

I found some other guides which guide me to use http://host.port/SMD but this is not supported anymore and it tells me I should use SOLMAN_SETUP instead (Diagnostic Setup or Diagnostic Administration). But also these two options I cannot find in SOLMAN_SETUP or SOLMAN_WORKCENTER.

I think the Wily itself is working and also the agents are connected properly but where can I find these "missing" steps?

Thanks

Pascal

Accepted Solutions (1)

Accepted Solutions (1)

former_member118647
Active Participant
0 Kudos

Hello Lehmann,

Screen shot given in setup guide for wily 8.0 after step 4 "Launch the Introscope Setup application" is taken from solman 7.0 release.

If you are using solman 7.0 release then go to solman_setup->managed system configuration->select your mangaed system and go to step 4 in guided procedure and click on open URL for  activity "Configure wily introscope agent"

this open the page something like given below, Select the server nodes and click on Apply to setup the IS Agent.

regards,

suhel

Former Member
0 Kudos

Dear Suhel,

Thanks but exactly this is the problem. This link is not working...in SM7.1 it is in step 7 "Automatic Configuration" and it refeers to http://SOLMAN_FQDN:PORT/webdynpro/sap.com/tc~smd~navigation/StandaloneApp?APP_ID=SMD_WILYADMIN_JAVA". But if I login with J2EE_ADMIN I got the message that this page is not available...

I can also see the system in the Wily Webview but this page where I can configure the agents is not accessible for me.

Thanks

Pascal

former_member118647
Active Participant
0 Kudos

Hello Pascal,

So you are saying that you are not able to execute activity "Byte code Adaptor installation" under step 7? But why are you executing this step individually. This Step 7 is fully automatic all you have to do is click on "execute all " button and configuration will take place automatically. Are you getting any error in this particular activiy? Please post the error.

More you said you are trying to login with J2EE_admin user. I will suggest you perform the step with user SOLMAN_ADMIN which gets created in step 1 of system preparation.

Regards,

Suhel

former_member206167
Active Participant
0 Kudos

Hi,  is mandatory to use Wily 9 abd correspondig management modules as per inst guide. Then repeat wily configuration under solman_setup

Regards

Former Member
0 Kudos

Dear Suhel,

No this step is working fine but there is a Link "Open JAVA URL" which should open the tool for configurating the Introscope Agent and this is not working. This link should open

http://SOLMAN_FQDN:PORT/webdynpro/sap.com/tc~smd~navigation/StandaloneApp?APP_ID=SMD_WILYADMIN_JAVA as I mentioned above.

I will try with SOLMAN_ADMIN and let you know if this works.

BTW: I am using Wily 9.1.15 now and not 8 anymore.

BR
Pascal

Answers (2)

Answers (2)

bxiv
Active Contributor
0 Kudos

Introscope 8 is an old version, the newest version is 9.1.5; I suggest you install the newer version before you run solman_setup on those systems.

However if you can't or don't want to upgrade and continue with 8, run through managed system setups for the systems you want to populate Wily and as part of Step 8 Configure Automatically it will setup the systems for you.

I can also tell you that with BO/BoE/BOBJ you will need to have that system have some configuration changes in order for the metrics to come into Wily; this is not  task on the Solution Manager side.

Former Member
0 Kudos

Hi,

Plz check the guide in https://websmp102.sap-ag.de/instguides   -> SAap component -> sap solution manager -> 7.1 version -> 2b


After install the Wily EM , open the webview url

http://<hostname>:8081/webview

Credential: user: Admin, password: Admin89

ftp://210.107.96.253/SOL_BACKUP_1115/usr/sap/Willy/docs/IntroscopeWebViewForSAPGuide.pdf

Also SAP recommend to use latest Wily  version. 

Once wily is up and running, follow the managed system setup for Bo system

http://wiki.scn.sap.com/wiki/display/SMSETUP/Managed+System+Setup+of+BOE+4.0+system+in+Solman+7.1

Refer last page wily setup for SAP BO system.

Please refer to Note 1540591 - Wily Introscope Setup for SAP BOE 4.0

Rg,

Karthik