Skip to Content
avatar image
Former Member

Problem with Wily Installation SM 7.1

Dear All,

We are facing some problems during the installation/configuration of Wily 8.0 in our system landscape.

The following tasks are done and seem to be OK:

- Installation of Wily Enterprise Manager 8.0 on our Solution Manager System

- Installation of Diagnostics Agent 7.3 on our Portal and BO Servers

- Agents are connected to the Solman

- Portal and BO System are configured in solman_setup including DA and Wily configuration

So far so good but in the Wily Introscope Guide there is a point where the agent is configurated (Chapter 4). We deployed the ISAGENTSMD* with SMD but the next point is "Lauch the Introscope Setup application". But where can I find this?

I found some other guides which guide me to use http://host.port/SMD but this is not supported anymore and it tells me I should use SOLMAN_SETUP instead (Diagnostic Setup or Diagnostic Administration). But also these two options I cannot find in SOLMAN_SETUP or SOLMAN_WORKCENTER.

I think the Wily itself is working and also the agents are connected properly but where can I find these "missing" steps?



Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

3 Answers

  • Best Answer
    Sep 26, 2013 at 04:32 AM

    Hello Lehmann,

    Screen shot given in setup guide for wily 8.0 after step 4 "Launch the Introscope Setup application" is taken from solman 7.0 release.

    If you are using solman 7.0 release then go to solman_setup->managed system configuration->select your mangaed system and go to step 4 in guided procedure and click on open URL for  activity "Configure wily introscope agent"

    this open the page something like given below, Select the server nodes and click on Apply to setup the IS Agent.



    Add comment
    10|10000 characters needed characters exceeded

    • Former Member Suhel Khan

      Dear Suhel,

      No this step is working fine but there is a Link "Open JAVA URL" which should open the tool for configurating the Introscope Agent and this is not working. This link should open

      http://SOLMAN_FQDN:PORT/webdynpro/ as I mentioned above.

      I will try with SOLMAN_ADMIN and let you know if this works.

      BTW: I am using Wily 9.1.15 now and not 8 anymore.


  • avatar image
    Former Member
    Sep 26, 2013 at 02:55 AM


    Plz check the guide in   -> SAap component -> sap solution manager -> 7.1 version -> 2b

    After install the Wily EM , open the webview url


    Credential: user: Admin, password: Admin89

    Also SAP recommend to use latest Wily  version. 

    Once wily is up and running, follow the managed system setup for Bo system

    Refer last page wily setup for SAP BO system.

    Please refer to Note 1540591 - Wily Introscope Setup for SAP BOE 4.0



    Add comment
    10|10000 characters needed characters exceeded

  • avatar image
    Former Member
    Sep 26, 2013 at 03:02 AM

    Introscope 8 is an old version, the newest version is 9.1.5; I suggest you install the newer version before you run solman_setup on those systems.

    However if you can't or don't want to upgrade and continue with 8, run through managed system setups for the systems you want to populate Wily and as part of Step 8 Configure Automatically it will setup the systems for you.

    I can also tell you that with BO/BoE/BOBJ you will need to have that system have some configuration changes in order for the metrics to come into Wily; this is not  task on the Solution Manager side.

    Add comment
    10|10000 characters needed characters exceeded