Skip to Content
author's profile photo Former Member
Former Member

0IC_C03 for populate data

Hi there

I really need help to populate data for Inventory InfoCube Material Movements 0IC_C03. Is there any body who tell me steps?

By the ways I have been reading SCN posts a lot and got so confuse.

Many Thanks

Sadia

Add a comment
10|10000 characters needed characters exceeded

Related questions

8 Answers

  • Best Answer
    author's profile photo Former Member
    Former Member
    Posted on Sep 05, 2013 at 06:18 AM

    The steps are below

    Step1: delete setup table

    Step2: run tcode MCNB for BX datasource only

    step3: run settup table for BF with posting date is 01.01.1000 to 31.12.9999 and UM datasource.

    step4: run full infopackage for BX, BF, UM

    step5: run DTP for BX with extraction mode is: Initial Non-Cumulative for Non-Cumulative Values and compress with marker update

    step6: run DTP for BF and compress with no marker update

    step7: run DTP for BF and compress with no marker update.

    step8: run init infopackage for BF and UM

    step9: run delta infopackage for BF, UM

    step10: run DTP and compress with marker update for BF,UM request.

    Good Luck!

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 05, 2013 at 05:51 AM

    Hi

    There is lots of step by step postings for 0ic_c03 in scn.

    Where is your confusion?

    Building up the data in ECC or the BW part?

    Martin

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Sep 05, 2013 at 05:55 AM

    This message was moderated.

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 05, 2013 at 05:55 AM

    Hi,

    If you say where you confused that would be better for us to clarify.

    Simple words.

    You need to LO data extraction steps for inventory extraction 0IC_C03

    You need to load data from data sources to Cube 0IC_C03 from source system.

    1. 2LIS_03_BX,

    2. 2LIS_03_BF

    3. 2LIS_03_UM.

    i assuming that your very familiar with BW ETL concepts.

    Thanks

    Add a comment
    10|10000 characters needed characters exceeded

  • author's profile photo Former Member
    Former Member
    Posted on Sep 05, 2013 at 06:25 AM

    Hi Sadia,

    There were good number of documents available related to loading data to 0IC_C03 cube. A basic search on SCN will give you the necessary documents.

    Also please refer this below links too.

    http://scn.sap.com/docs/DOC-41821

    http://scn.sap.com/thread/2083026

    You can go ahead by using Anshus' reply wherein which you can come across step by step approach with screenshots of loading data to 0IC_C03 cube or else simple approach of Arshiyans' reply.

    Thanks,

    Karan Lokesh.

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 05, 2013 at 06:26 AM

    In ECC tcode MB5B and MC.9 is used for validating the data of 0IC_C03.

    Explore more about your query.

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 05, 2013 at 06:17 AM

    Hi Sadia,

    A simple search would have given you lot of documents related to inventory.

    Please check the below document.

    http://scn.sap.com/docs/DOC-35750

    In case you have any particular issue or doubt related to it then please post it so that experts can share their views on the same.

    Hope that helps.

    Regards,
    AL

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Sep 06, 2013 at 07:24 AM

    Hi Saida,

    is your doubt was cleared??

    Thanks

    Add a comment
    10|10000 characters needed characters exceeded

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.