Skip to Content
author's profile photo Former Member
Former Member

Error when creating transfer structure /BIC/CCOJ0FI_AR_4 in source system

Hi,

I enhanced datasource 0FI_AR_4 with two new fields in ECC and replicated datasource into BW. But when I try to activate the datasource, I am getting message "Error when creating transfer structure /BIC/CCOJ0FI_AR_4 in source system".

I try to activate datasource manually and by using program RS_TRANSTRU_ACTIVATE_ALL, but endup with a same error message.

To fix this issue I created programs as per the Note 493422, but it will work only in R/3 3.1 system. The Note 564599 is for 7.X datasources. This note is not available and getting "The requested SAP Note is either in reworking or is released internally only".

Please let me know if have any suggestions to fix this issue.

Thanks,

Hemanth

Add a comment
10|10000 characters needed characters exceeded

Related questions

7 Answers

  • Best Answer
    Posted on Jul 17, 2013 at 08:29 AM

    Check the RFC connection between your source system and BW.

    Are you able to see data in RSA3? Check it is active in RSA6.

    Try to replicate again and activate it manually.

    Add a comment
    10|10000 characters needed characters exceeded

    • Former Member Suman Chakravarthy K

      Issue got resolved. Thanks for all suggestion.

      Our BI system had duplicate source ECC system connected. Due to which ROOSGEN table in source system had few entries generated when I try to activate. Which lead to the activation failure. After deleting this entries in ROOSGEN table, I was able to activate successfully.

      Thanks,

      Hemanth

  • author's profile photo Former Member
    Former Member
    Posted on Jul 17, 2013 at 10:47 AM

    Hi,

    Please check the table ROOSFIELD. What is the "field attr" of the enhanced fields?

    Are you able to see the data in RSA3?

    Thanks,

    Amir

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Jul 17, 2013 at 10:48 AM

    Hi Hemanth,

    Migrate your data source using tcode RSDS from 3.x to 7.x then again migrate it from 7.x to 3.x.

    Now try to create your transfer rule.

    Regards,
    Abdullah

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Jul 17, 2013 at 11:13 AM

    Hi Hemanth,

    Are you facing this after system copy?.

    Do you have two source system connections with same source system technical name?

    Check whether source system is active or not. Do a source system connection check in RSA1.

    Also,check WE20 and WE21 and see of partner profile is active and correctly configured or not.

    Srikanth.

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Jul 17, 2013 at 02:18 PM

    Just delete the PSA data wrt following transfer strcuture and reimport the transport again in the system.

    also check following thread

    Error creating transfer structure in source system

    check below thread

    http://scn.sap.com/thread/2097730

    Thanks and regards

    Kiran

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Jul 17, 2013 at 08:08 PM

    Hi Hemanth

    The note 493422 has a valid correction for ALL releases. If the source system is 7.0x or above, use the report
    Z_RS_SCRSYSTEM_R3_CHECK without any parameters to list all inconsistencies.

    Then run it in repair mode and the activation will work.

    There is no need to delete the datasource/data itself.

    br

    Roland

    Add a comment
    10|10000 characters needed characters exceeded

  • Posted on Oct 21, 2019 at 05:37 AM

    In the source system, delete the related datasource in the ROOSGENSEG and ROOSGEN tables and re-active it in the BW system.

    Add a comment
    10|10000 characters needed characters exceeded

Before answering

You should only submit an answer when you are proposing a solution to the poster's problem. If you want the poster to clarify the question or provide more information, please leave a comment instead, requesting additional details. When answering, please include specifics, such as step-by-step instructions, context for the solution, and links to useful resources. Also, please make sure that you answer complies with our Rules of Engagement.
You must be Logged in to submit an answer.

Up to 10 attachments (including images) can be used with a maximum of 1.0 MB each and 10.5 MB total.