CDMC : CTS Analysis

[Former Member]

I have set up an analysis for a transport request in CDMC, but I am not getting any usage data of the objects of the transport request.

I have set the system as follows:

Control System: Solution Manager (None)

Analysis system: DEV system

Statistics sytem: PRD system

Target System : QAS system

But when i run the test result for test scope analysis or test coverage analysis, not data is displayed.

[Former Member · Accepted solution]

hi

have you activated the statistics collection for PRD system, if active only you can get the test scope identification result. result of test scope analyser depends on statistic collection information of Analysis system too.

so after adding the system activate statistics collection for both statistics and analysis system

refer sap note 1244713 - Configuration of Custom Development Management Cockpit and the attached guide.

Thanks

Jansi

[Former Member · Accepted solution]

Yes we have activated the statistic collection in PRD, and defined the system in "Maintain statistics collection"

[Former Member · Accepted solution]

Hi Jansi

Can you please confirm me if i have selected the right systems for right role

Control System: Solution Manager (None)

Analysis system: DEV system

Statistics sytem: PRD system

Target System : QAS system

Further I have enabled statistics collection for all the three system, still  usage data dosent appear in analysis result.

[Former Member · Accepted solution]

Hi,

These are my findings

- you shouldnt activate statistics for all system. it should be only for PRD. your analysis system and control system can be same. you can see the guide for recommendation, but your case its okie. no prb, but remove the other system from stat collection

- more over its all depends on your ST03N data, means initial run only store the 3 months data. as i could see your stat collection for PRD shows 387 programs. should display result is t? what is the output of display result, any other view you can see the result, check the stat collection job logs any error?

-  Test scope identificaion s shows the used objects in stat system, check also in environmental view, any data there?

- all your analysis goes fine, have you checked logs of analysis jobs? and spool reports? any error.

- Make sure you have sufficient auth assinged.

Regards

Jansi

[Former Member · Accepted solution]

Hi Jansi

Really appreciate your reply. I have deleted the stat collection for rest of the systems. Below is the status of all the jobs

When I seee the log of all the jobs for collect and anlysis phase, performed in DEV system, however i have define my statistics system PRD. How to schedule/run the job for PRD system??

Below is the screenshot for test scope identification log:

[Former Member · Accepted solution]

hi

you can see the help information about what is each task about in near icon. you can also get the information about where each task run. Test scope identification runs only on analysis system, your analysis system s ur dev system, so it runs on DEV box.

Again it all depends on the data we collected and data we planned to compare. I could see all of your jobs finshed less then 3 min, it not the case, we hav jobs runs more than 8 hrs too.

specially some wrong with the task Determine Object? its shws zero runtime. this is the very important, its actually goes as input for other analysis like test scope identification

Please check

Regards

Jansi

[Former Member · Accepted solution]

Can you please guide me what system i should assign for each role?

Target system?

Analysis system?

since statistics system can only be PRD, right?

[Former Member · Accepted solution]

Hi

i can answer you again, but may i ask have you refer the guide in the note 1244713 or atleast help information attached in each and every task? its given open statement which system define which role

if we can read this before proceed any task, this could help to move to proper way or atleast help to fix the error we stuck.

Thanks

Jansi

[Former Member · Accepted solution]

Many thanks Jansi for your support, really appreciate it. Yes I have referred the guide earlier, as it states

Control System (C): This is the system which acts as the control center. The

administration of a CTS project is carried out from a system with this role, and all activities

(even the ones that run in one of the other systems) are triggered from here. The control

system should be the central SAP Solution Manager system.

Analysis System (A): This is the system where all project-related analyses (including

selection of relevant objects in a transport request) are executed, and the results are stored

in a CDMC database table.

Target System (T): This is the system in which the object set in the transport request

(selected during the activity Determine Object Set) would be released to. In the analysis

activities like Remote Comparison and Perform Environment Analysis, the version of the

object in the analysis system is compared against with the target system.

Statistics System (S): In the statistics system, the collection of statistical data takes

place. A job that is executed periodically (daily or weekly) transfers and condenses SAP

standard statistics data and short dump evaluation in a CDMC database table. This is an

optional system and should be added only if you need to  check the usage of objects inside

transport requests.

The conclusion i reached is that

If Analysis system:QAS, target would be PRD

and if Analysis system :QAS then target would ne PRD??

Secondly when i select QAS as analysis system, it asks to activate stat collection for it??

I would really appreciate your support

Kind Regards