Skip to Content
avatar image
Former Member

source of supply for in-house production --> Error in Consistency Check for CTM Master Data

Hello all,

we are using SCM 7.0 EHP 1.

I'm trying to implement CTM and running an error whenever I try to start a CTM Planning Run. The Run breaks with an Error massages, which says that the source of supply (for the end product) is without a plan.

So I started the consistency check for CTM Master Data and got the same error message:

Message no. /SAPAPO/CTM1350

No plan exists for in-house production source of supply XXX

Does anybody know if I need a Plan in the in-house production source and if yes, why do I need it?

How can I get rid of this error?

Would be thankful for any ideas.

Thank you very much and kindest regards,

Eva Mauerer

Add comment
10|10000 characters needed characters exceeded

  • Get RSS Feed

4 Answers

  • Best Answer
    avatar image
    Former Member
    Jul 09, 2013 at 09:30 PM

    Hi Eva,

    I would suggest you to run the consistency check for  CTM master data using the t.code

    /SAPAPO/CTM01 , If you are not getting any errors there , Please  go thru the below sap note :

    Note 1380927 - CTM Sources of supply for In-House production selection

    Hope this helps

    Rgds,

    Kiru

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member Former Member

      Hi Eva:

      In response to your question:

      ========

      Also not quite sure if note 1689736 is helpful because we did not already implement note 1592408.

      @Shweta: Did your alreade implement 1592408?

      ========

      We are using SCM 720 now. Note 1592408 has already been implemented on

      our system.We just need to go ahead with note 1689736 now.

      I hope this information could help.

      Thanks and Kind regards,

      Shweta

  • avatar image
    Former Member
    Jul 06, 2013 at 08:25 PM

    Hi Eva,

    Looks like there is problem with the PPM/Plan of your end product.

    Go to the tcode /sapapo/scc03 and open the PPM of the end product for which you are running CTM and getting error.

    For products with inhouse production, CTM needs a valid PPM/Plan.

    Regards,

    Mitesh

    Add comment
    10|10000 characters needed characters exceeded

  • Jul 07, 2013 at 04:57 AM

    Hii Eva,

    If the Product is going to be in house production, It must have BOM, Routing and PV in ECC side. You must CIF them to APO as well. We CIF them as PPM/PDS from ECC to APO. Which generally acts as a source of supply and used for Production planning.

    If you want to run PPDS/CTM you want to activate PPM?PDS IM in ECC, and have to send the BOM,PV of this SKU to APO.  Then only the planned orders generated from CTM can pick the right source of supply, and also can CIF to ECC as well

    Regards

    Debashis

    Add comment
    10|10000 characters needed characters exceeded

    • Former Member Former Member

      Eva,

      Can you check the settings for "Plan Explosion" under PP/DS tab in material master in APO ?

      It should have 5 or blank value since you are using PDS. If it is blank then in customizing you should have set "PDS" as the default plan explosion.

      By ignoring all the master data, you are ignoring the values for all those parameters like production horizon, stock transfer horizon, quota arrangement, calendars etc. which could have create issues for you if you have valid values for these parameters.

      Regards,

      Mitesh

      PDS.jpg (71.9 kB)
  • avatar image
    Former Member
    Jul 09, 2013 at 06:47 PM

    Hi Eva,

    We were also getting the same error and hence raised to SAP. They suggested to implement the following note:

    Note 1689736 - CTM master data check fails on PDS

    We still are under process of implementing it.. i would advice you to implement this and see if it works.

    Do let me know the results 😊

    Also, plz mark this answer as helpful if it is !

    Thanks and regards,

    Shweta

    Add comment
    10|10000 characters needed characters exceeded